UUK1A330MCO Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
UK 6mmL Chip Type, For general Audio Equipment
series
Chip type acoustic series.
Applicable to automatic insertion machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC)
UK
Chip MW
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
Stability at Low Temperature
Performance Characteristics
– 40 ~ +85°C
4 ~ 50V
0.1 ~ 220µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
tan δ (MAX.)
4
0.35
6.3
0.26
10
0.20
16
0.16
25
0.14
35
0.12
50
0.12
Measurement frequency : 120Hz
Rated voltage (V)
4
6.3
10
16
25
35
50
Impedance ratio Z– 25°C / Z+20°C
7
4
3
2
2
2
2
ZT / Z20 (MAX.) Z– 40°C / Z+20°C 15
8
8
4
4
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
After 2000 hours' application of rated voltage
at 85°C, capacitors meet the characteristics
requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ± 20% of initial value
200% or less of initial specified value
Initial specified value or less
After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristics requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
Capacitance
Lot No.
∗Voltage Plastic platform
0.3MAX.
C±0.2
L±0.3
∗Voltage mark for 6.3V is 6V .
Dimensions
0.5 ~ 0.8
Positive
Negative
φD ₄
(mm)
5 6.3
A 1.8 2.1 2.4
B 4.3 5.3 6.6
C 4.3 5.3 6.6
E 1.0 1.3 2.2
L 5.8 5.8 5.8
Type numbering system (Example : 16V 10µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UU K 1 C 1 0 0 MCO 1 GS
Taping code
Size code
Configuration
Rated Capacitance tolerance (±20%)
Capacitance (10µF )
Rated voltage (16V )
Series name
Type
Cap.(µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
220
V
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
221
4
0G
4
28
4
33
5
56
6.3
96
6.3
0J
4
28
5
37
5
45
6.3
70
10
1A
5
33
5
41
6.3
52
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
10 kHz~
1.50
16
1C
4
23
5
37
6.3
49
6.3
58
25
1E
4
16
5
27
6.3
42
6.3
52
35
1V
4
18
5
29
6.3 46
50
1H
4
1.0
4
2.0
4
2.8
4
4.0
4
8.4
4
13
4
17
5
20
6.3 33
Case size φ D
Rated
ripple
Rated Ripple(mArms)at 85°C 120Hz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given
in page 25, 26.
Please refer to page 3 for the minimum order quantity.
CAT.8100V