UUD1C220MCL1GS Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
UD Chip Type, Low Impedance
series
Chip type, low impedance temperature range up to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
WD
High
Te m p reflow
CD ^{Low Impedance}
UD
Low Impedance WG
Specifications
Item
Performance Characteristics
Category Temperature Range – 55 to +105°C
Rated Voltage Range
6.3 to 50V
Rated Capacitance Range 1 to 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater.
Tangent of loss angle (tan δ)
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
6.3
10
16
25
35
50
tan δ (MAX.) 0.26 (0.28) 0.20 (0.24) 0.16 (0.20) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14)
( ) is φ8 over
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Stability at Low Temperature _{Impedance ratio Z– 25°C / Z+20°C}
3
2
2
2
2
2
ZT / Z20 (MAX.) Z– 55°C / Z+20°C
5
4
4
3
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
The specifications listed at right shall be met
when the capacitors are restored to 20°C after the
rated voltage is applied for 5000 hours (2000
hours for φD = 4, 5 and 6.3) at 105°C.
Capacitance change
tan δ
Leakage current
Within ±30% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate
and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
(φ4 to φ6.3)
Voltage (C:16V)
Series
Plastic platform
0.3 MAX.
C±0.2
Positive
Lot No.
Capacitance
(φ8 to φ10 )
Voltage (V:35V)
Series
Trade mark
L±0.3
Plastic platform
0.3 MAX.
H
C±0.2
Negative
Positive
Lot No.
Capacitance
L±0.5
Pressure relief vent
Voltage
V 6.3 10 16 25 35 50
Code j A C E V H
Dimension table in next page.
Negative
H
Type numbering system (Example : 16V 22µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UUD 1C 2 2 0 M CL 1GS
Package code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (22µF)
Rated voltage (16V)
φD
4 to 6.3
8 • 10
Code
CL
NL
Series name
Type
φ D × L _{4 × 5.8}
A
1.8
B
4.3
C
4.3
E
1.0
L
5.8
H
0.5 to 0.8
5 × 5.8
2.1
5.3
5.3
1.3
5.8
0.5 to 0.8
6.3 × 5.8
2.4
6.6
6.6
2.2
5.8
0.5 to 0.8
6.3 × 7.7
2.4
6.6
6.6
2.2
7.7
0.5 to 0.8
8 × 10
2.9
8.3
8.3
3.1
10
0.8 to 1.1
(mm)
10 × 10
3.2
10.3
10.3
4.5
10
0.8 to 1.1
CAT.8100C