UUD0J270MCL Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
UD Chip Type, Low Impedance
series
Chip type, low impedance temperature range up to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
WD
CD ^{Low Impedance}
High
Te m p reflow
UD
Low Impedance WG
Specifications
Item
Performance Characteristics
Category Temperature Range – 55 ~ +105°C
Rated Voltage Range
6.3 ~ 50V
Rated Capacitance Range 1 ~ 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater.
tan δ
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
6.3
10
16
25
35
50
tan δ (MAX.) 0.26 (0.28) 0.20 (0.24) 0.16 (0.20) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14)
( ) is φ8 over
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Stability at Low Temperature _{Impedance ratio Z– 25°C / Z+20°C}
3
2
2
2
2
2
ZT / Z20 (MAX.) Z– 55°C / Z+20°C 5
4
4
3
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
After 5000 hours' (2000 hours for φD 6.3)
application of rated voltage at 105°C , capacitors
meet the characteristic requirements listed at
right.
Capacitance change
tan δ
Leakage current
Within ±30% of initial value
200% or less of initial specified value
Initial specified value or less
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
(φ4 ~ 6.3)
Voltage (C:16V)
Series
Plastic platform
0.3 MAX.
C±0.2
Positive
Lot No.
Capacitance
(φ8×10, φ10×10 )
Voltage (V:35V)
Series
Trade mark
L±0.3
H
Plastic platform
0.3 MAX.
C±0.2
Negative
Positive
Lot No.
Capacitance
L±0.5
Pressure relief vent
Voltage
V 6.3 10 16 25 35 50
Code j A C E V H
Dimension table in next page.
Negative
H
Type numbering system (Example : 16V 22µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UUD 1C 2 2 0 M CL 1GS
Package code
Configuration
Capacitance tolerance (–20%)
Rated Capacitance (22µF)
Rated voltage (16V)
φD
4 ~ 6.3
8 ¥ 10
Code
CL
NL
Series name
Type
φ D × L _{4 × 5.8}
A
1.8
B
4.3
C
4.3
E
1.0
L
5.8
H
0.5 ~ 0.8
5 × 5.8
2.1
5.3
5.3
1.3
5.8
0.5 ~ 0.8
6.3 × 5.8
2.4
6.6
6.6
2.2
5.8
0.5 ~ 0.8
6.3 × 7.7
2.4
6.6
6.6
2.2
7.7
0.5 ~ 0.8
8 × 10
2.9
8.3
8.3
3.1
10
0.8 ~ 1.1
(mm)
10 × 10
3.2
10.3
10.3
4.5
10
0.8 ~ 1.1
CAT.8100V