UUB1A470MCL Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
UB Chip Type, High Reliability
series
Chip type, high temperature range, for +125°C use.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
WH
High
Temperature
Reflow
CJ
Added ESR specification
at – 40°C
UB
High
Temperature
UX
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
Performance Characteristics
– 40 ~ +125°C
10 ~ 50V
10 ~ 330µF
± 20% at 120Hz, 20°C
After 1 minute's application of rated voltage, leakage current is not more than 0.03CV or 4(µA) , whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
tan δ (MAX.)
10
0.32
16
0.24
25
0.21
35
0.18
50
0.18
Rated voltage (V)
10
Stability at Low Temperature
Impedance ratio _{Z– 40°C / Z+20°C}
ZT / Z20 (MAX.)
12
Measurement frequency : 120Hz
16
25
35
50
8
6
4
4
Endurance
After 2000 hours' (φ8 × 6.2 : 1000 hours) application
of rated voltage at 125°C, capacitors meet the
characteristic requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±30% of initial value
300% or less of intial specified value
Initial specified value or less
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 125°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
(φ8 × 6.2)
125¡C Marking
Capacitance
Plastic platform
Voltage
0.3MAX.
C±0.2
Lot No.
Trade mark
L±0.3
H
(φ8 × 10, φ10 × 10)
125¡C Marking
LTroatdNeom.ark
Capacitance
Voltage
Plastic platform
0.3MAX.
C±0.2
L±0.5
Pressure relief vent
H
Type numbering system (Example : 10V 100µF)
Positive
U¹ U² B³ 1⁴ A⁵ 1⁶ 0⁷ 1⁸ M^{9 1}C⁰ L^{11 1}1² G¹³ S¹⁴
Negative
Positive
Negative
(mm)
fD´L _{8´6.2 8´10 10´10}
A 3.3 2.9 3.2
B 8.3 8.3 10.3
C 8.3 8.3 10.3
E 2.3 3.1 4.5
L 6.2 10 10
H 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1
Taping code
Configuration
Capacitance tolerance (±20%) fD ´ L Code
Rated Capacitance (100mF)
Rated voltage (10V)
8 ´ 6.2
8 ´ 10
10 ´ 10
CL
NL
NL
Series name
Type
Dimensions
Cap.(µF)
10
22
33
47
100
220
330
V
Code
100
220
330
470
101
221
331
10
1A
8 × 6.2
58
8 × 10
90
10 × 10
112
16
1C
8 × 10
66
10 × 10
102
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
10 kHz~
1.50
25
1E
8 × 6.2
48
8 × 10
74
10 × 10
116
35
1V
8 × 6.2
8 × 10
10 × 10
50
1H
8 × 6.2
24
8 × 6.2
38
44
8 × 10
46
52
10 × 10
58
80
Case size
φ D × L (mm)
Rated
ripple
Rated Ripple (mArms) at 125°C 120Hz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given in page 25, 26.
Please select UH(p.78) series if high CV products are required.
Please refer to page 3 for the minimum order quantity.
CAT.8100V