UUB1A101MCL1GS Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
UB Chip Type, High Reliability
series
Chip type, high temperature range, for +125°C use.
Applicable to automatic mounting machine
fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
(Through 50V only)
WH
LT
High
Temperature
Reflow
High
Voltage
CJ
Added ESR specification
at – 40°C
UB
High
Temperature
UX
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
– 40 to +125°C
10 to 400V
1 to 330µF
± 20% at 120Hz, 20°C
Rated voltage (V)
Leakage Current
Tangent of loss angle (tan δ)
Rated voltage (V)
tan δ (MAX.)
10
0.32
Performance Characteristics
10 to 50
After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (µA).
Measurement frequency : 120Hz at 20°C
16
25
35
50
160
200
250
0.24
0.21
0.18
0.18
0.30
0.30
0.30
160 to 400
I = 0.04CV+100 ( µA) max.(1 minute's)
400
0.30
Measurement frequency : 120Hz
Rated voltage (V)
10
16
25
35
50
160 200 250 400
Stability at Low Temperature
Impedance ratio _{Z– 40°C / Z+20°C}
ZT / Z20 (MAX.)
12
8
6
4
4
8
8
8
12
Endurance
Shelf Life
Resistance to soldering
heat
Marking
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours (1000 hours for φ8 × 6.2) at 125°C.
Capacitance change
tan δ
Leakage current
Within ±30% of the initial capacitance value
300% or less than the intial specified value
Less than or equal to the initial specified value
After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds,
which is maintained at 250°C. The capacitors shall meet
the characteristic requirements listed at right when they
are removed from the plate and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
(φ8 × 6.2)
125°C Marking
Capacitance
Lot No.
Plastic platform
Voltage
0.3MAX.
C±0.2
Positive
Type numbering system (Example : 10V 100µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UUB 1 A 1 0 1 MCL 1GS
Taping code
Trade mark
Configuration
L±0.3
Negative
H
Capacitance tolerance (±20%) φD × L
Rated capacitance (100µF) ^{8 × 6.2}
8 × 10
Rated voltage (10V) _{10 × 10}
Code
CL
NL
NL
(φ8 × 10, φ10 × 10)
125°C Marking
Lot No.
Capacitance
Trade mark
Voltage
Plastic platform
0.3MAX.
C±0.2
L±0.5
Pressure relief vent
H
Dimensions
Positive
Negative
(mm)
φD × L _{8 × 6.2 8 × 10 10 × 10}
A 3.3 2.9 3.2
B 8.3 8.3 10.3
C 8.3 8.3 10.3
E 2.3 3.1 4.5
L 6.2 10 10
H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1
Series name
Type
Cap.(µF)
010
022
033
047
100
220
330
V
Code
100
220
330
470
101
221
331
10
1A
8 × 6.2
58
8 × 10
90
10 × 10
112
16
1C
8 × 10
66
10 × 10
102
25
1E
8 × 6.2
48
8 × 10
74
10 × 10
116
35
1V
8 × 6.2
44
8 × 10
52
10 × 10
80
50
1H
8 × 6.2
8 × 6.2
8 × 10
10 × 10
Case size
φ D × L (mm)
24
38
46
58
Rated
ripple
Cap.(µF)
1
1.8
2.2
3.3
4.7
6.8
10
V
Code
010
1R8
2R2
3R3
4R7
6R8
100
160
2C
8 × 10 42
10 × 10 59
200
250
400
2D
2E
2G
8 × 10 26
8 × 10 27
10 × 10 36
8 × 10 28 10 × 10 38
8 × 10 36 10 × 10 59
10 × 10 59
10 × 10 59
Case size Rated
φ D × L (mm) ripple
Rated ripple current (mArms) at 125°C 120Hz
Frequency coefficient of rated ripple current
Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10kHz or more
Coefficient 0.70 1.00 1.17 1.36 1.50
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in
page 18, 19.
Please refer to page 3 for the minimum order quantity.
CAT.8100C