UPW1C222MHH Datasheet, PDF (1/5 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
PW Low lmpedance, High Reliability
For Switching Power Supplies
series
Smaller case size and lower impedance than PM series.
Low impedance and high reliability withstanding 2000 hours to 8000 hours.
Capacitance ranges available based on the numerical values in E12 series
under JIS.
PM
Smaller
PW
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Performance Characteristics
– 55 ~ +105˚C (6.3 ~ 100V), – 40 ~ + 105˚C (160 ~ 400V), – 25 ~ +105˚C (450V)
6.3 ~ 450V
0.47 ~ 15000µF
± 20% at 120Hz, 20˚C
Leakage Current
Rated voltage (V)
Leakage current
6.3 ~ 100
After 1 minute's application of rated voltage, leakage current
is not more than 0.03CV or 4 (µA), whichever is greater.
160 ~ 450
CV ^<= 1000 : I = 0.1CV+40 (µA) max. (1 minute's)
CV > 1000 : I = 0.04CV+100 (µA) max. (1 minute's)
tan δ
For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF.
Measurement frequency : 120Hz, Temperature : 20˚C
Rated voltage (V) 6.3
10
16
25
35
50
63
100 160 ~ 250 315 · 350 400 · 450
tan δ (MAX.) 0.22
0.19
0.16
0.14
0.12
0.10
0.09
0.08
0.15
0.20
0.25
Rated voltage (V)
6.3 · 10 16 · 25 35 · 50 63 · 100 160 · 200 250 315 · 350 400
Stability at Low Temperature
Z– 55˚C / Z+20˚C
3
3
3
3
—
—
—
—
Impedance ratio Z– 40˚C / Z+20˚C
—
—
—
—
4
6
8
10
Z– 25˚C / Z+20˚C
—
—
—
—
3
3
4
6
120Hz
450
—
—
15
Endurance
Shelf Life
After an application of D.C. bias voltage plus the rated ripple
current for 8000 hours (2000 hours for D = 4, 5 and 6.3,
3000 hours for D = 8, 5000 hours for D = 10, 7000 hours for
D = 12.5) at 105˚C the peak voltage shall not exceed the
rated D.C.voltage, capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±20% of initial value
200% or less of initial specified value
Initial specified value or less
After leaving capacitors under no load at 105˚C for 1000 hours, they meet the specified value for endurance characteristics listed
Marking
Printed with white color letter on dark brown sleeve.
Radial Lead Type
Sleeve (P.E.T.)
φd
L+ ^MAX
15^MIN
4^MIN
Pressure relief vent
φ 6.3up (No pressure relief vent for 7mmL products)
(L = 7) 1.0
(L < 20) 1.5
(L 20) 2.0
φD 4 5 6.3 8
P 1.5 2.0 2.5 3.5
φd
0.45 0.5 0.5 0.6
(0.45) (0.45)
0.5 0.5 0.5 0.5
: Applied to L>25 products
( ): Applied to 7mmL products
10 12.5 16
5.0 5.0 7.5
0.6 0.6 0.8
0.8
0.5 0.5 0.5
18 20 22 25
7.5 10.0 10.0 12.5
0.8 1.0 1.0 1.0
0.5 0.5 1.0 1.0
Frequency coefficient of rated ripple current
V
6.3 ~ 100
Cap. (µF) ^Frequency
..~ 56
68 ~ 330.
390 ~ 1000.
.1200 ~ 15000
50Hz
0.20
0.55
0.70
0.80
120Hz
0.30
0.65
0.75
0.85
160 ~ 450
0.47 ~ 2200
330 ~ 470.
0.80
1.00
0.90
1.00
300Hz
0.50
0.75
0.80
0.90
1.25
1.10
1kHz
0.80
0.85
0.90
0.95
1.40
1.13
Type numbering system (Example : 10V 680µF)
1 2 3 4 5 6 7 8 9 10 11 12
U PW 1 A 6 8 1 MP D
Size code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (680µF)
Rated voltage (10V)
Series name
Type
Configuration
φD
Pb free lead finishing Sn-Pb lead finishing
Pb free PET sleeve PVC sleeve contain Pb
4·5
DD
DH
6.3
ED
EH (7mm L : DH)
8 · 10
PD
PH
12.5 ~ 18
HD
HH
20 ~ 25
RD
RH
Please contact to us if other configurations are required.
10kHz ~
1.00
1.00
1.00
1.00
1.60
1.15
Please refer to page 19, 20, 21 about the formed or taped product spec.
Please refer to page 3 for the minimum order quantity.
Dimension table in next page.
CAT.8100S