ULR2G8R2MNL1GS Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
LR Chip Type, High Voltage.
series
Chip Type, high Voltage.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2011/65/EU).
LV
Long Life
LR
High
Voltage
UX
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
– 40 to +105°C
160 to 500V
2.7 to 39µF
± 20% at 120Hz, 20°C
After 1 minute's application of rated voltage, leakage current is not more than 0.04CV +100(µA).
Measurement frequency : 120Hz at 20°C
Rated voltage (V) 160
tan δ (MAX.) 0.20
200
0.20
250
0.25
400
0.25
450
0.30
500
0.30
Stability at Low Temperature
Rated voltage (V)
160
Impedance ratio
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
6
Measurement frequency: 120Hz
200 250 400 450 500
6
10 10 15 15
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 3000 hours at 105°C.
Capacitance change
tan δ
Leakage current
Within ±20% of the initial capacitance value
200% or less than the intial specified value
Less than or equal to the initial specified value
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C and then performing voltage treatment based on
JIS C 5101-4 clause 4.1 at 20°C, they shall meet the characteristic
requirements listed at right when they are removed from the plate.
Black print on the case top.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Chip Type
(φ8 × 10L, φ10)
Voltage(2G : 400V)
Series
Lot No.
Trade mark
Plastic platform
0.3MAX.
C±0.2
Positive
Capacitance
L±1.0
Pressure relief vent
Negative
H
(mm)
φD × L _{8 × 10 10 × 10 10 × 13.5}
A 2.9 3.2 3.2
B 8.3 10.3 10.3
C 8.3 10.3 10.3
E 3.1 4.5 4.5
L
10
10 13.5
H 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Voltage
V 160 200 250 400 450 500
Code 2C 2D 2E 2G 2W 2H
Type numbering system (Example : 400V 8.2µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
ULR 2G 8R2 MNL 1GS
Taping code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (8.2µF)
Rated voltage (400V)
Series name
Type
Dimensions
Cap.(µF)
2.7
3.9
4.7
5.6
6.8
8.2
10
12
15
22
27
33
39
V
Code
2R7
3R9
4R7
5R6
6R8
8R2
100
120
150
220
270
330
390
160
2C
8 × 10 50
10 × 10 65
10 × 13.5 70
200
2D
8 × 10 50
10 × 10 65
10 × 13.5 70
Frequency coefficient of rated ripple current
Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10kHz or more
Coefficient 0.80 1.00 1.25 1.40 1.60
250
2E
8 × 10 35
10 × 10 50
10 × 13.5 55
400
2G
8 × 10
35
10 × 10
50
10 × 13.5 55
450
2W
8 × 10
25
10 × 10
40
10 × 13.5 45
500
2H
8 × 10
20
10 × 10
35
10 × 13.5 40
Case size Rated
φ D × L (mm) ripple
Rated ripple current (mArms) at 105°C 120Hz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please refer to page 3 for the minimum order quantity.
CAT.8100C