UCM1C101MCL1GS Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
CM Chip Type, Low Impedance
series
Chip type, low impedance temperature range up to +105°C.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
CL
Smaller
Higher capacitance
CM
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Performance Characteristics
– 55 to +105°C
6.3 to 50V
10 to 2200µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV
Rated voltage (V)
tan δ (MAX.)
6.3
0.26
10
0.19
16
0.16
25
0.14
35
0.12
50
0.10
Rated voltage (V)
6.3
10
16
25
35
50
Stability at Low Temperature
Impedance ratio
ZT / Z20 (MAX.)
Z– 25°C / Z+20°C
Z– 40°C / Z+20°C
2
3
2
3
2
3
2
3
2
3
2
3
Z– 55°C / Z+20°C
4
4
4
3
3
3
Measurement frequency : 120Hz at 20°C
Measurement frequency : 120Hz
Endurance
Shelf Life
Resistance to soldering
heat
Marking
The specifications listed at right shall be met
when the capacitors are restored to 20°C after the
rated voltage is applied for 2000 hours at 105°C.
Capacitance change
tan δ
Leakage current
Within ±30% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate
and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
(φ4 to φ6.3)
Voltage( C : 16V )
Series
Plastic platform
0.3MAX.
Lot No.
Capacitance
(φ8 × 10L, φ10 )
Voltage( E : 25V )
Trade mark
Series
L 0.3
Plastic platform
0.3MAX.
Lot No.
Capacitance
L 0.5
Pressure relief vent
C 0.2
H
C 0.2
H
Positive
Negative
Positive
Negative
Type numbering system (Example : 16V 100µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
U CM 1 C 1 0 1 M C L 1 GS
Capacitance tolerance (±20%)
Rated capacitance (100µF)
Rated voltage (16V)
Series name
Type
Taping code
Size code
Configuration
φD
4 to 6.3
8 · 10
Code
CL
NL
φD×L _{ × }
 ×   ×   ×   × 
(mm)
 × 
"






#






$






&






-






) 
UP
 
UP
 
UP
 
UP
 
UP
 
UP

Voltage
V 6.3 10 16 25 35 50
Code j A C E V H
Dimension table in next page.
CAT.8100C