UCL1E221MCL6GS Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
CL Chip Type, Low Impedance
series
Chip type, low impedance, temperature range up to +105°C.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2002/95/EC).
CL
Low Impedance _CD
Specifications
Item
Performance Characteristics
Category Temperature Range – 55 to +105°C
Rated Voltage Range
6.3 to 50V
Rated Capacitance Range
10 to 2200µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater.
Tangent of loss angle (tan δ)
Rated voltage (V)
tan δ (MAX.)
Measurement frequency : 120Hz at 20°C
6.3
10
16
25
35
50
0.26
0.19
0.16
0.14
0.12
0.10
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Stability at Low Temperature
Z—25°C / Z+20°C
Impedance ratio
2
2
2
2
2
2
ZT / Z20 (MAX.) ^{Z—40°C / Z+20°C}
3
3
3
3
3
3
Z—55°C / Z+20°C
4
4
4
3
3
3
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance Change
tan δ
Leakage current
Within ± 30% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
Shelf Life
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at
20°C, they shall meet the specified values for the endurance characteristics listed above.
Resistance to soldering
heat
Marking
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate
and restored to 20°C .
Capacitance Change
tan δ
Leakage current
Black print on the case top.
Within ± 10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Chip Type
(φ4 to φ8 × 6.2)
Voltage (C : 16V )
1 Trade mark
Series name
Plastic platform
0.3 MAX.
C± 0.2
Positive
Lot No.
Capacitance
L± 0.3
1: Size φ8 × 6.2 only
(φ8 × 10L, φ10)
Voltage (E : 25V)
Series name
Trade mark
Plastic platform
0.3 MAX.
H
C± 0.2
Negative
Positive
Pressure 2
relief vent
L± 0.5
Lot No.
Capacitance
2 : Except : φ10 × 7.7L
H
Voltage
V
6.3
10
16
25
35
50
Code
j
A
C
E
V
H
Dimension table in next page.
Negative
Type numbering system (Example : 16V 100µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UCL 1C 1 0 1 M CL 1 GS
Capacitance tolerance (±20%)
Rated capacitance (100µF)
Rated voltage (16V)
Series name
Type
Taping code
Size code
Configuration
φ D Code
4 to 6.3 CL
8 (6.2L) CL
10(7.7L) CL
8(10L) •
10(10L,13.5L)
NL
φD×L
4 × 5.8
5 × 5.8 6.3 × 5.8 6.3 × 7.7 8 × 6.2
(mm)
8 × 10 10 × 7.7 10 × 10 10 × 13.5
A
1.8
2.1
2.4
2.4
3.3
2.9
3.2
3.2
3.2
B
4.3
5.3
6.6
6.6
8.3
8.3
10.3 10.3 10.3
C
4.3
5.3
6.6
6.6
8.3
8.3
10.3 10.3 10.3
E
1.0
1.3
2.2
2.2
2.3
3.1
4.5
4.5
4.5
L
5.8
5.8
5.8
7.7
6.2
10
7.7
10
13.5
H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
CAT.8100B