UCJ1A101MCL1GS Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
CJ Chip Type, High Reliability.
Low temperature ESR specification.
series
Chip type, high temperature range, for +125°C use.
Added ESR specification after the test at –40°C
(φ6.3 sizes provide only for the first stage. )
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
CZ
Low ESR
Long Life
CJ
Added ESR specification
at – 40°C
UB
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Performance Characteristics
– 40 to +125°C
10 to 50V
10 to 470µF
± 20% at 120Hz, 20°C
After 1 minute's application of rated voltage, leakage current is not more than 0.03CV or 4(µA) , whichever is greater.
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
tan δ (MAX.)
10
0.32
16
0.24
25
0.21
35
0.18
50
0.18
Stability at Low Temperature
Rated voltage (V)
Impedance ratio _{Z– 40°C / Z+20°C}
ZT / Z20 (MAX.)
10
12
Measurement frequency : 120Hz
16
25
35
50
8
6
4
4
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 125°C.
Capacitance change
tan δ
Leakage current
Within ±30% of the initial capacitance value
300% or less than the intial specified value
Less than or equal to the initial specified value
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds,
which is maintained at 250°C. The capacitors shall meet
the characteristic requirements listed at right when they
are removed from the plate and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
(φ6.3)
Voltage( C : 16V )
Series
Plastic platform
0.3MAX.
C ± 0.2
Positive
Type numbering system (Example : 10V 100µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UC J 1 A 1 0 1 MCL 1GS
Taping code
Configuration
Lot No.
Capacitance
L ± 0.3
Negative
H
Capacitance tolerance (±20%)
Rated capacitance (100µF)
Rated voltage (10V)
(φ8 to φ10)
Voltage( V : 35V )
Trade mark
Series
Plastic platform
0.3MAX.
Lot No.
Capacitance
L ± 0.5
Dimensions
Cap.(µF)
10
22
33
47
100
220
330
470
V
10
Code
1A
100
220
330
470
101 6.3 × 8.7 14 - 95
221
8 × 10 2.0 6.0 250
331 10 × 10 1.5 4.5 400
471 10 × 10 1.5 4.5 400
C ± 0.2
H
16
1C
6.3 × 8.7 14
8 × 10 2.0
10 × 10 1.5
10 × 10 1.5
Positive
Negative
6.3 × 8.7
6.3 × 8.7
- 95 6.3 × 8.7
6.0 250 8 × 10
4.5 400 10 × 10
4.5 400 10 × 10
(mm)
φD × L _{6.3 × 8.7 8 × 10 10 × 10}
A 2.4 2.9 3.2
B 6.6 8.3 10.3
C 6.6 8.3 10.3
E 2.2 3.1 4.5
L 8.7 10 10
H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1
25
35
1E
1V
6.3 × 8.7 14
14 - 95 6.3 × 8.7 14
14 - 95 6.3 × 8.7 14
14 - 95 6.3 × 8.7 14
2.0 6.0 250 10 × 10 1.5
1.5 4.5 400 10 × 10 1.5
1.5 4.5 400
Series name
Type
Rated Voltage
V 10 16 25 35 50
Code A C E V H
50
1H
- 95 6.3 × 8.7 14 - 95
- 95 6.3 × 8.7 14 - 95
- 95 8 × 10 2.0 6.0 200
- 95 10 × 10 1.5 4.5 330
4.5 400 10 × 10 1.5 4.5 330
4.5
400
after
Case size
φD × L
(mm)
Initial endurance _Rated
test _ripple
ESR
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more
Coefficient
0.35
0.50
0.64
0.83
1.00
Max. ESR (Ω) at -40°C 100kHz, Rated ripple current (mArms) at 125°C 100kHz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
CAT.8100C