UCJ1A100MCL Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
CJ Chip Type, High Reliability.
Low temperature ESR specification.
series
Chip type, high temperature range, for +125°C use.
Added ESR specification after the test at –40°C
(φ6.3 sizes provide only for the first stage. )
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
CJ
Added ESR specification
at – 40°C
UB
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
Performance Characteristics
– 40 ~ +125°C
10 ~ 50V
10 ~ 470µF
± 20% at 120Hz, 20°C
After 1 minute's application of rated voltage, leakage current is not more than 0.03CV or 4(µA) , whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
tan δ (MAX.)
10
0.32
16
0.24
25
0.21
35
0.18
50
0.18
Rated voltage (V)
10
Stability at Low Temperature
Impedance ratio _{Z– 40°C / Z+20°C}
ZT / Z20 (MAX.)
12
Measurement frequency : 120Hz
16
25
35
50
8
6
4
4
Endurance
After 2000 hours' application of rated voltage at
125°C, capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±30% of initial value
300% or less of intial specified value
Initial specified value or less
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 125°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
(φ6.3 × 8.7)
Voltage( C : 16V ) _Series
Plastic platform
0.3MAX.
Type numbering system (Example : 10V 100µF)
Positive
C±0.2
U¹ C² J³ 1⁴ A⁵ 1⁶ 0⁷ 1⁸ M^{9 1}C⁰ L^{11 1}1² G¹³ S¹⁴
Lot No.
Capacitance
(φ8 × 10, φ10 × 10)
Voltage( V : 35V )
Trade mark
Series
Lot No.
Capacitance
L±0.3
Plastic platform
0.3MAX.
L±0.5
H
Negative
Positive
C±0.2
Negative
H
(mm)
fD´L _{6.3´8.7 8´10 10´10}
A 2.4 2.9 3.2
B 6.6 8.3 10.3
C 6.6 8.3 10.3
E 2.2 3.1 4.5
L 8.7 10 10
H 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1
Taping code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (100mF)
Rated voltage (10V)
Series name
Type
Dimensions
Cap.(µF)
10
22
33
47
100
220
330
470
V
10
16
25
35
50
Code
1A
1C
1E
1V
1H
100
6.3 × 8.7 14 - 95 6.3 × 8.7 14 - 95
220
6.3 × 8.7 14 - 95 6.3 × 8.7 14 - 95 6.3 × 8.7 14 - 95
330
6.3 × 8.7 14 - 95 6.3 × 8.7 14 - 95 8 × 10 2.0 6.0 200
470
6.3 × 8.7 14 - 95 6.3 × 8.7 14 - 95 6.3 × 8.7 14 - 95 10 × 10 1.5 4.5 330
101 6.3 × 8.7 14 - 95 8 × 10 2.0 6.0 250 8 × 10 2.0 6.0 250 10 × 10 1.5 4.5 400 10 × 10 1.5 4.5 330
221
331
471
8 × 10
10 × 10
10 × 10
2.0 6.0 250 10 × 10
1.5 4.5 400 10 × 10
1.5 4.5 400
1.5 4.5 400 10 × 10
1.5 4.5 400 10 × 10
1.5 4.5 400 10 × 10
1.5 4.5 400
1.5
4.5 400
after
Case size
φD × L
(mm)
Initial torture _Rated
test _ripple
ESR
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.35
0.50
0.64
0.83
10 kHz~
1.00
Max. ESR (Ω) at -40°C 100kHz, Rated Ripple (mArms) at 125°C 100kHz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given in page 25, 26.
Please refer to page 3 for the minimum order quantity.
CAT.8100V-2