UCD1A220MCL Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
CD Chip Type, Low Impedance
series
Chip type, low impedance temperature range up to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
CD
Low Impedance _UD
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
Stability at Low Temperature
Performance Characteristics
– 55 ~ +105°C
6.3 ~ 100V
1 ~ 3300µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
tan δ (MAX.)
6.3
10
16
25
35
50
63
80
100
0.26 0.19 0.16 0.14 0.12 0.10 0.08 0.08 0.07
For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF.
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
63
80
100
Z—25°C / Z+20°C 2
2
2
2
2
2
2
2
2
Impecance ratio
ZT / Z20 (MAX.) ^{Z—40°C / Z+20°C}
3
3
3
3
3
3
3
3
3
Z—55°C / Z+20°C 4
4
4
3
3
3
3
3
3
Endurance
After 5000 hours' (2000 hours for L 10 mm: 50V
Capacitance Change
or less, and for L 10mm: 63V or more) application of
tan δ
rated voltage at 105°C, capacitors meet the characteristics
requirements listed at right.
Leakage current
Within ± 30% of initial value for capacitors
200% or less initial specified value
300% or less initial specified value for 63V or more
Initial specified value or less
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at
20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristics requirements
listed at right.
Black print on the case top.
Capacitance Change
tan δ
Leakage current
Within ± 10% of initial value
Initial specified value or less
Initial specified value or less
Chip Type
(φ4 ~ φ8 × 6.2)
Voltage ( j : 6.3V )
Series
1 Trade mark
Plastic platform
0.3 MAX.
C± 0.2
Positive
Lot No.
Capacitance
(φ8 × 10, φ10 × 10)
Voltage (E : 25V)
Series
Trade mark
L± 0.3
Plastic platform
0.3 MAX.
H
Negative
1: Size φ8 × 6.2 only
Positive
C± 0.2
Lot No.
Pressure
relief vent
Capacitance
L± 0.5
(φ12.5 ~ φ18)
Trade mark Voltage
Lot No.
Plastic platform
0.3 MAX.
H
C± 0.2
Negative
Positive
Capacitance
Pressure
relief vent
Series
L± 1.0
Dimension table in next page.
H
Negative
Type numbering system (Example : 16V 100µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UCD 1C 1 0 1 M CL 1 GS
Package code
Size Package Code
φ4 ~ 10 Taping GS
φ12.5 ~ 18 Taping MS
φ12.5 ~ 18 Tray
ZD
Size code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (100µF)
Rated voltage (16V)
Series name
φ D Code
4 ~ 6.3 CL
8 (6.2L) CL
8(10L) •10 NL
12.5~18 NQ
Type
(mm)
φ D × L _{4 × 5.8 5 × 5.8 6.3 × 5.8 6.3 × 7.7 8 × 6.2 8 × 10 10 × 10}
A
1.8
2.1
2.4
2.4
3.3
2.9
3.2
B
4.3
5.3
6.6
6.6
8.3
8.3
10.3
C
4.3
5.3
6.6
6.6
8.3
8.3
10.3
E
1.0
1.3
2.2
2.2
2.3
3.1
4.5
L
5.8
5.8
5.8
7.7
6.2
10
10
H
0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1
φ D × L _{12.5 × 13.5 16 × 16.5 18 × 16.5}
A
4.8
5.4
6.4
B
13.6
17.1
19.1
C
13.6
17.1
19.1
E
4.0
6.3
6.3
L
13.5
16.5
16.5
H
1.0 ~ 1.4 1.0 ~ 1.4 1.0 ~ 1.4
Voltage
V
6.3 10 16 25 35 50 63 80 100
Code
j
A
C
E
V
H
J
K 2A
CAT.8100V-3