PLG0G122MCO1_15 Datasheet, PDF (1/2 Pages) Nichicon corporation – CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
PLG ^{Radial Lead Type, Higher Capacitance}
Higher Capacitance, Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence
Compliant to the RoHS directive (2011/65/EU).
PLG
Higher
Capacitance
PLF
Specifications
Item
Performance Characteristics
Category Temperature Range – 55 to +105°C
Rated Voltage Range
2.5 to 16V
Rated Capacitance Range 330 to 3900µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2)
Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25
Z– 55°C / Z+20°C 1.25
(100kHz)
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions prescribed
here as preheat at 150 to 200°C for 60 to 180 seconds and peak
temperature at 265°C for 10 seconds or less, the capacitor shall meet
the specifications listed at right, provided that its temperature profile is
measured at both of terminal ends facing the soldering side.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Resin coated Case
Voltage(g:4V)
Series
Lot. No.
L+0.5MAX.
φd
15MIN
4MIN
(mm)
Size φ8 × 9L φ8 × 12L φ10 × 13L
φD
8.0
8.0
10.0
Voltage
L
8.5
P
3.5
φd
0.6
11.5
12.5
3.5
5.0
0.6
0.6
V
2.5 4 6.3 10 16
Code
e
g
j
A
C
Please refer to page 20 about the end seal configuration.
Type numbering system (Example : 4V 1200µF)
1 2 3 4 5 6 7 8 9 10 11 12
P LG 0G 1 2 2 MCO 1
Size code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (1200µF)
Rated voltage (4V)
Series name
Type
Dimension table in next page.

CAT.8100E