PLF0E561MCO1 Datasheet, PDF (1/2 Pages) Nichicon corporation – CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LF Radial Lead Type, Standard
series
Ultra Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence.
Adapted to the RoHS directive (2002/95/EC).
Specifications
Item
Performance Characteristics
Category Temperature Range – 55 ~ +105°C
Rated Voltage Range
2.5 ~ 16V
Rated Capacitance Range 270 ~ 1000µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
tan δ
Not more than value of Standard ratings at 120Hz, 20°C
ESR ( 1)
Not more than value of Standard ratings at 100kHz, 20°C
Leakage Current ( 2) Not more than value of Standard ratings. After 2 minute's application of rated voltage.
Characteristics of Temperature _{Z+105°C / Z+20°C 1.25 (100kHz)}
Impedance Ratio
Z– 55°C / Z+20°C 1.25
20°C
Endurance
After 2000 hours' application of rated voltage
at 105°C, capacitors meet the specified value
for life characteristics listed at right.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
Damp Heat
Resistance to
Soldering Heat
Marking
After 1000 hours' application of rated voltage
at 60°C 90%RH, capacitors meet the specified value
for life characteristics listed at right.
To comply with recommended conditions for
reflow soldering. Pre-heating shall be done
at 150 ~ 200°C and for 60 ~ 180 sec.
Peak temp. is 265°C, within 10 sec.
Measurement for solder temperature profile shall
be made at a point on the terminal nearest where
the terminals protrude through the soldering side
of PC board.
Navy blue print on the case top
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of initial value ( 3)
130% or less of the initial specified value
130% or less of the initial specified value
Initial specified value or less
1 ESR measurements should be made at a point on the terminal nearest the end seal of the capacitor.
2 Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the
temperature of 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Laminated Case
Voltage(g:4V)
Silvered lead Wire
Type numbering system (Example : 4V 560µF)
Taping code
Series
Lot. No.
L+0.5MAX.
(mm)
Size φ8 × 9L φ8 × 12L φ10 × 13L
φD
8.0
8.0
10.0
L
8.5
11.5
12.5
P
3.5
3.5
5.0
φd
0.6
0.6
0.6
Voltage
V 2.5 4 6.3 10 16
Code e g j A C
φd
15MIN
4MIN
Please refer to page 21 about the end seal configulation.
Dimension table in next page.
CAT.8100V