PCX1C470MCL1GS Datasheet, PDF (1/2 Pages) Nichicon corporation – CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CX Chip Type, High Voltage / Long Life
series
High reliability, High voltage (to 50V).
Low ESR, High ripple current.
Long life of 1500 to 3000 hours at 125°C.
SMD type : Lead free reflow soldering condition at
260°C peak complete correspondence.
Adapted to the RoHS directive (2011/65/EU).
CR
Higher
Capacitance
CX
Higher
Temperature
Specifications
CV
Item
Performance Characteristics
Category Temperature Range – 55 to +125°C
Rated Voltage Range
16 to 50V
Rated Capacitance Range 5.6 to 390µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+125°C / Z+20°C 1.25
Z– 55°C / Z+20°C 1.25
(100kHz)
Endurance
The specifications listed at below shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 3000 hours (φD = 6.3:1500hours) at 125°C.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of initial capacitance value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at below shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of initial capacitance value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
Marking
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Type numbering system (Example : 35V 39µF)
Dimensions
Standard
Capacitance
Lot No.
Plastic platform
0.3 MAX.
C±0.2
Positive
1 2 3 4 5 6 7 8 9 10 11 12 13 14
PCX 1 V 3 9 0 MC L 1 GS
Taping code
Size code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (39µF)
Rated voltage (35V)
Configuration code
Standard
L
Vibration Resistance S
Series
Voltage (V:35V)
L
+0.1
- 0.4
Negative
Series name
Type
Vibration Resistance
Capacitance
Lot No.
Plastic platform
0.3 MAX.
H
C±0.2
Positive
Standard
(mm) Vibration Resistance (mm)
Size φ6.3 × 6L φ6.3 × 8L φ8 × 7L φ8 × 10L φ8 × 12L φ10 × 8L φ10 × 10L φ10×12.7L Size φ6.3 × 8L φ8 × 7.5L φ8 ×10.5L φ10 ×10.5L
φD 6.3 6.3 8.0 8.0 8.0 10.0 10.0 10.0 φD 6.3 8.0 8.0 10.0
L 5.9 7.9 6.9 9.9 11.9 7.9 9.9 12.6 L 7.5 7.0 10.0 10.0
A 7.3 7.3 9.0 9.0 9.0 11.0 11.0 11.0 A 7.3 9.0 9.0 11.0
B 6.6 6.6 8.3 8.3 8.3 10.3 10.3 10.3 B 6.6 8.3 8.3 10.3
C 6.6 6.6 8.3 8.3 8.3 10.3 10.3 10.3 C 6.6 8.3 8.3 10.3
Series
Voltage (V:35V)
L±0.5
Negative
H
Aid electrode
E 2.1 2.1 3.2 3.2 3.2 4.6 4.6 4.6
H 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Voltage
V 16 20 25 35 50
E 2.5 2.5 3.1 4.6
H 0.5 to 0.8 0.8 to 1.1 1.1 to 1.5 1.1 to 1.5
Dimension table in next page.
Code C D E V H
CAT.8100C