PCF0E101MCL1GS Datasheet, PDF (1/2 Pages) Nichicon corporation – CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CF Chip Type, Standard
series
Ultra Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at 260°C peak
correspondence.
Adapted to the RoHS directive (2002/95/EC).
Specifications
Item
Performance Characteristics
Category Temperature Range – 55 ~ +105°C
Rated Voltage Range
2.5 ~ 25V
Rated Capacitance Range 6.8 ~ 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
tan δ
Not more than value of Standard ratings at 120Hz, 20°C
ESR ( 1)
Not more than value of Standard ratings at 100kHz, 20°C
Leakage Current ( 2) Not more than value of Standard ratings. After 2 minute's application of rated voltage.
Characteristics of Temperature _{Z+105°C / Z+20°C 1.25}
Impedance Ratio
Z– 55°C / Z+20°C 1.25
(100kHz)
20°C
Endurance
After 2000 hours' application of rated voltage
at 105°C, capacitors meet the specified value
for life characteristics listed at right.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
Damp Heat
After 1000 hours' application of rated voltage
at 60°C 90%RH, capacitors meet the specified value
for life characteristics listed at right.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
Resistance to
Soldering Heat
Marking
To comply with recommended conditions for
reflow soldering. Pre-heating shall be done
at 150 ~ 200°C and for 60 ~ 180 sec.
In the case of peak temp, less than 250°C,
reflow soldering shall be within two times.
In the case of peak temp, less than 260°C,
reflow soldering shall be once.
Measurement for solder temperature profile shall
be made at the capacitor top and the terminal.
Navy blue print on the case top
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of initial value ( 3)
130% or less of the initial specified value
130% or less of the initial specified value
Initial specified value or less
1 ESR measurements should be made at a point on the terminal nearest where the terminals protrude through the plastic platform.
2 Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the
temperature of 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Lot No.
Plastic platform
0.3 MAX.
C±0.2
Positive
Type numbering system (Example : 6.3V 150µF)
Series
Voltage ( j:6.3v)
L ^+-00..41
H
Size
φ6.3 × 6L
φD
6.3
L
5.9
A
7.3
B
6.6
C
6.6
E
2.1
H
0.5 ~ 0.8
φ8 × 7L
8.0
6.9
9.0
8.3
8.3
3.2
0.8 ~ 1.1
φ10 × 8L
10.0
7.9
11.0
10.3
10.3
4.6
0.8 ~ 1.1
(mm)
φ10 × 10L
10.0
9.9
11.0
10.3
10.3
4.6
0.8 ~ 1.1
Dimension table in next page.
Negative
Voltage
V
2.5 4 6.3 10 16 20 25
Code
e
g
j
A
C
D
E
CAT.8100V