LNY2G152MSEF Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
NY Screw Terminal Type, 85°C Higher Capacitance
series
Suited for equipment down sizing.
Load life of 2000 hours application of ripple current at 85°C
Compliant to the RoHS directive (2011/65/EU).
NY
High
Voltage
NR
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Insulation Resistance
Voltage proof
Endurance
Shelf Life
Marking
Performance Characteristics
– 40 to +85°C
350 to 450V
820 to 22000µF
± 20% (120Hz, 20°C)
After 5 minutes' application of rated voltage, leakage current is not more than 3 _CV (µA) or 5 mA, whichever is smaller. (at 20°C)
[C : Rated Capacitance(µF), V : Voltage ( V ) ]
0.25MAX. (120Hz at 20°C)
Rated voltage(V)
Impedance ratio ZT/Z20(MAX.)
350 to 450
Z – 40°C / Z+20°C
12
Measurement frequeny : 120Hz
The insulation resistance shall be more than 100MΩ at DC 500V application between terminal and bracket.
There is no abnormality during AC 2500V 1 minute's application between terminal and bracket.
The specifications listed at right shall be met when the capacitors are
restored to 20°C after D.C. bias plus rated ripple current is applied for
2000 hours at 85°C, the peak voltage shall not exceed the rated
voltage.
Capacitance change
tan δ
Leakage current
Within ±20% of the initial capacitance value
300% or less than the initial specified value
Less than or equal to the initial specified value
After storing the capacitors under no load at 85°C for 1000 hours Capacitance change
and then performing voltage treatment based on JIS C 5101-4 tan δ
clause 4.1 at 20°C, they shall meet the reguirements listed at right. _{Leakage current}
Printed with white color letter on black sleeve
Within ±20% of the initial capacitance value
300% or less than the initial specified value
Less than or equal to the initial specified value
Drawing
Bottom plate
Sleeve
120^°
Hexagenal headed bolt
Pressure relief vent
h
H^±1
L^{+ MAX.}
B
±1
B
3-leg brackets for φ 90 capacitors have different
hole shapes from the ordinary ones illustrated
below.
P
7
Note) The brackets will be supplied in the separate box.
P^±2
T
A^±2
U
U
S
Pressure relief vent
30_°
Type numbering system (Example:400V 10000 F)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
L NY 2G 1 0 3 MSE J
Configuration
Capacitance tolerance (± 20%)
Rated Capacitance (10000 F)
Rated Voltage (400V)
Series name
Type
Case dia. code
φD
051.0
063.5
076.2
090.0
Code
F
G
H
J
Mounting bracket
(φ51 to φ90)
3-leg brackets Code less
2-leg brackets BB
No brackets BN
Configuration
Cr (III) Plating
(RoHS compliant)
SE
Please refer to page 330 for schematic of dimensions.
Please contact to us if PVCless products are required.
Dimension of terminal pitch (W) and length (
φD
W
51
22.0
6
63.5
28.6
6
76.2
31.8
6
90
31.8
6
) and Nominal dia. of bolt
(mm)
α
Nominal dia. of bolt
3
M5
3
M5
3
M5
3
M5
Dimension table in next page.
Dimension of mounting bracket
Symbol
Leg shape
φD ₅₁
3-Leg
63.5 76.2
P
32.5 38.1 44.5
A
38.5 43 49.2
T
7.5 8.0 7.0
S
5.0 5.0 5.0
U
12 14 14
°
60 60 60
H
20 25 30
h
15 20 24
90
50.8
58.5
8.0
5.0
18
60
35
25
2-Leg
51 63.5 76.2
33.2 40.5 46.5
40 46.5 53
6.0 7.0 6.0
4.5 4.5 4.5
14 14 14
30 30 30
25 35 35
15 20 20
(mm)
90
53
59
6.0
4.5
14
30
35
20
CAT.8100C