LNT2W123MSEJ Datasheet, PDF (1/5 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
NT Screw Terminal Type, 105°C Standard
series
Load life of 5,000 hours (2,000 hours for 10~250V,500V) application
of rated ripple current at +105°C.
Extended voltage range from 10V up to 500V.
Extended range up to φ100 × 250L 2size.
Compliant to the RoHS directive (2011/65/EU).
NT
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle
(tan δ) (MAX)
Smaller
High Voltage
NU
High
Te m p e r ature
NR
Performance Characteristics
– 40 to +105°C (10 to 100V) , – 25 to +105°C (160 to 500V)
10 to 500V
220 to 1500000µF
± 20% at 120Hz, 20°C
After 5 minutes’ application of rated voltage, leakage current is not more than 3 CV (µA) or 5mA, whichever is smaller. (at 20°C) [C:Rated Capacitance (µF) , V:Voltage(V)]
Measurement frequency:120Hz, Temperature:20°C
φD
L
V 10
16
25
35
80 to 100
0.65
0.45
0.4
35
50
63
80
100 160 to 250 350 to 500
0.3
0.25
0.25
0.2
0.12
0.15
0.2
80 to 100 0.80
0.6
0.5
0.4
0.25
0.25
0.2
0.15
0.15
0.2
51
120
0.85
0.6
0.5
0.4
0.3
—
—
—
—
0.2
100
—
—
0.65
—
0.35
0.3
0.25
0.2
0.2
0.2
63.5
110 to 130
1.2
0.8
0.7
0.5
0.35
0.3
—
—
0.2
0.2
100
2.0
1.2
0.9
0.7
0.55
0.5
0.3
0.3
—
0.2
76.2
120 to 150
2.0
1.2
0.9
0.7
0.55
0.5
0.35
0.3
0.2
0.2
90 140 to 220 2.4
2.0
1.5
1.0
0.75
0.6
0.4
0.3
0.25
0.2
100 220 • 250
2.4
2.0
1.5
1.0
0.75
0.6
0.4
0.3
0.25
0.2
Stability at Low Temperature
Rated voltage(V)
Impedance ratio
Z – 25°C/ Z+20°C
ZT/Z20(MAX.)
Z – 40°C/ Z+20°C
10 to 100
—
12
160 to 500
8
—
Measurement frequency : 120Hz
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after D.C. bias plus rated
ripple current is applied for 5000 hours (2000 hours for 10 to
250V/500V) at 105°C, the peak voltage shall not exceed the
rated voltage.
Capacitance change
tan δ
Leakage current
Within ±20% of the initial capacitance value
300% or less than the initial specified value
Less than or equal to the initial specified value
Shelf Life
After storing the capacitors under no load at 105°C
for 1000 hours and then performing voltage treatment
based on JIS C 5101-4 clause 4.1 at 20°C,
they shall meet the requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±20% of the initial capacitance value
300% or less than the initial specified value
Less than or equal to the initial specified value
Marking
Drawing
φ 35 Screw terminal type
Bottom plate _Sleeve
Printed with white color letter on black sleeve.
Hexagenal headed bolt (M5)
Pressure relief vent
10
15±0.5
L^+3MAX.
6±1
+
7
24
29±1
Dimension table in next page.
Type numbering system
Voltage 250V or less (Example : 250V 3300µF)
1 2 3 4 5 6 7 8 9 10 11 12
L NT 2 E 3 3 2 MS E
Mounting bracket
Configuration (φ35)
Capacitance tolerance (±20%) Code less 2-leg brackets
Rated capacitance (3300µF) N No brackets
Rated voltage (250V) _{(φ51 to φ100)}
Series name _{Code less 3-leg brackets}
Type _{B 2-leg brackets}
N No brackets
Voltage 350V or more (Example : 450V 2200µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
L NT 2W 2 2 2 M SE G
Mounting bracket
Configuration
Case dia. code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (2200µF)
Rated voltage (450V)
Series name
Type
φD Code
35 C
51 F
63.5 G
76.2 H
90 J
100 K
(φ35)
Code less 2-leg brackets
BN No brackets
(φ51 to φ90)
Code less 3-leg brackets
BB 2-leg brackets
BN No brackets
(φ100)
Code less 3-leg brackets
BN No brackets
Cr ( III) Plating
(RoHS compliant)
SE
Please refer to page 330 for schematic of dimensions.
Please contact to us if PVCless products are required.
CAT.8100C