LLS2G680MELY Datasheet, PDF (1/6 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
LS Snap-in Terminal Type, 85°C Standard
series
Withstanding 3000 hours application of rated ripple current at 85°C.
Compliant to the RoHS directive (2011/65/EU).
LS
Smaller
LG
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Performance Characteristics
– 40 to +85°C (16 to 250V), – 25 to +85°C (350 to 450V)
16 to 450V
56 to 56000µF
± 20% at 120Hz, 20°C
I 3 CV (µA) (After 5 minutes' application of rated voltage) [C : Rated Capacitance (µF) V : Voltage (V)]
Measurement frequency :120Hz at 20°C
Rated voltage (V)
tan δ (MAX.)
16
0.50
25
0.40
35
0.35
50
0.30
63
0.25
80
0.20
100
0.20
160
0.15
180
0.15
200
0.15
250
0.15
350
0.15
400
0.15
450
0.20
Rated voltage (V)
Impedance ratio Z – 25°C/ Z+20°C
ZT/Z20(MAX.) _Z – _{40°C/ Z+20°C}
16 to 100
4
20
Measurement frequency : 120Hz
160 to 250
350 to 450
3
8
12
—
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after D.C. bias plus
rated ripple current is applied for 3000 hours at 85°C,
the peak voltage shall not exceed the rated voltage.
Capacitance change
tan δ
Leakage current
Within ±20% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
Shelf Life
Marking
After storing the capacitors under no load at 85°C
for 1000 hours and then performing voltage treatment
based on JIS C 5101-4 clause 4.1 at 20°C,
they shall meet the requirements listed at right.
Printed with white color letter on black sleeve.
Capacitance change
tan δ
Leakage current
Within ±15% of the initial capacitance value
150% or less than the initial specified value
Less than or equal to the initial specified value
Drawing
Polarity bar
Sleeve (P.E.T.)
L^±2
Pressure relief vent
10 _±0.1
10
4.0±0.5
0.8
+0.2
-0.1
0.8^+-00.2.1
Type numbering system ( Example : 200V 390µF)
1 2 3 4 5 6 7 8 9 10 11 12
L L S 2 D 3 9 1 ME L Z
Configuration
Capacitance tolerance(±20%)
Rated capacitance(390µF)
Rated voltage(200V)
Series name
Type
Case dia.code
φ D Code
20
Y
22
Z
25
A
30
B
35
C
2-2φ ±0.1
1.5
+0.2
-0.1
(PC board hole dimensions)
(Terminal dimensions)
The other terminal is also available upon request.
Please refer to page 328 for schematic of dimensions.
Frequency coefficient of rated ripple current
Frequency (Hz)
50
60
120
300
16 to 100V
0.88
0.90
1.00
1.07
160 to 250V
0.81
0.85
1.00
1.17
350 to 450V
0.77
0.82
1.00
1.16
Minimum order quantity : 50pcs.
1k
1.15
1.32
1.30
10k 50k or more
1.15
1.15
1.45
1.50
1.41
1.43
Dimension table in next page.
CAT.8100C