|
LAS Datasheet, PDF (1/2 Pages) TT Electronics. – 0.1 ohm to 18K ohms | |||
|
ALUMINUM ELECTROLYTIC CAPACITORS
LAS Snap-in Terminal Type,â 105°C Permissible Abnormal Voltage,
Smaller-sized
Withstanding 2000 hours application of rated ripple current of 105°C.
Addition of 450V rated voltage.
Smaller case sizes and higher ripple current than LAQ.
Improved safety features for abnormally excessive voltage.
Ideally suited for the equipment used at voltage fluctuating area.
Compliant to the RoHS directive (2011/65/EU).
LAQ
Smaller
LAS
Expanded
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Endurance
Performance Characteristics
â25 to +105°C
400 ⢠420 ⢠450V
56 to3 3C9V0µF
± 20%3 aCtV120Hz, â20°C
3 CV (µA) (After 5âminutes' application of rated voltage) [C : Rated Capacitance (µF) V : Voltage (V)]
0.20MAX.â120Hz at 20°C
Rated voltage(V)
Impedance ratio (MAX) Z â 25°C/Z+20°C
400ã»420ã»450
8
Measurement frequencyâ:â120Hz
The specifications listed at right shall be met when the
capacitors are restored to 20°C after D.C. bias plus rated
ripple current is applied for 2000 hours at 105°C, the
peak voltage shall not exceed the rated voltage.
Capacitance change
tan δ
Leakage current
Within ±20% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
Shelf Life
Safety Performance
Marking
After storing the capacitors under no load at 105°C for 1000
hours and then performing voltage treatment based
on JIS C 5101-4 clause 4.1 at 20°C,
they shall meet the requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±15% of the initial capacitance value
150% or less than the initial specified value
Less than or equal to the initial specified value
The pressure relief vent will operate in normal conditions,ââwith no dangerous conditions such as flames, âignitions or dispersion of pieces of the capacitor andâ/âor case.
Rating
Test conditions
Voltage (V)
Rated Capacitance (µF)
Limited DC current
Test voltage
330ââââ ââCââ<ââ100
2A
400
100ââ ââCââ<ââ220
4A
500VDC and 600VDC
220ââ ââCââ<ââ470
7A
330ââââ âCâ ââ<ââ100
420
100ââ ââCââ<ââ220
2A
4A
520VDC and 630VDC
220ââ ââCââ<ââ470
7A
330ââââ âCâ ââ<ââ100
450
100ââ ââCââ<ââ220
2A
4A
550VDC and 675VDC
220ââ ââCââ<ââ470
7A
Printed with white color letter on black sleeve
Drawing
Bottom plate
(code ZB only)
Polarity bar
Sleeve (P.E.T.)
L±2
Pressure relief vent
Ê¢10Ê£
4.0±0.5
0.8
+0.2
-0.1
0.8+-00..21
Type numbering system (Example : 400V 100µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
LAS 2G 1 0 1 ME L Z 2 5
Configuration
Capacitance tolerance (±20%)
Rated capacitance (100µF)
Rated voltage (400V)
Series name
Type
Case length code
Case dia. code
ÏD Code
22
Z
25
A
30
B
35
C
Bottom Plate
ZB
code less
With Bottom
Plate
Without
Bottom Plate
Please contact to us if other configurations are required.
1.5
+0.2
-0.1
(PC board hole dimensions)
(Terminal dimensions)
Frequency coefficient of rated ripple current
Frequency (Hz)
50
60
120
1k
Coeff. 400 · 420 · 450V
0.88
0.9
1.00
1.10
Minimum order quantity : 50pcs.
Dimension table in next page.
10k or more
1.15
|
▷ |