LAQ2D330MEL Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
AQ Snap-in Terminal Type, Permissible Abnormal Voltage, Smaller-sized,
Wide Temperature Range
(692 type) series
Withstanding 2000 hours application of rated ripple current of 105°C.
Extended voltage range at 200V, 220V and 400V.
Smaller case sizes and higher ripple current than AK series.
Improved safety features for abnormally excessive voltage.
Ideally suited for the equipment used at voltage fluctuating area.
Adapted to the RoHS directive (2002/95/EC).
AK
Smaller
AQ
Specifications
Item
Performance Characteristics
Category Temperature Range
–25 ~ +105°C
Rated Voltage Range
200 • 220 • 400V
Rated Capacitance Range 33 ~ 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
tan δ
Stability at Low Temperature
I 3 CV (µA) (After 5 minutes' application of rated voltage) ^[C : Rated Capacitance (µF) V : Voltage (V)]
0.20MAX. 120Hz, 20°C
Rated voltage(V)
Impedance ratio (MAX) Z – 25°C/Z+20°C
200 • 220
8
400
8
Measurement frequency : 120Hz
Endurance
After an application of DC voltage (in the range of rated
DC voltage even after over-lapping the specified ripple
current) for 2000 hours at 105°C, capacitors meet
the characteristic requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±20% of initial value
200% or less of initial specified value
Initial specified value or less
Shelf Life
Safety Performance
Marking
After storing the capacitors under no load at 105°C for 1000
hours, and after performing voltage treatment based
on JIS C 5101-4 clause 4.1 at 20°C,
they will meet the requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±15% of initial value
150% or less of initial specified value
Initial specified value or less
The pressure relief vent will operate in normal conditions, with no dangerous conditions such as flames, ignitions or dispersion of pieces of the capacitor and / or case.
Rating
Test conditions
Voltage (V)
Rated Capacitance (µF)
Limited DC current
Test voltage
330 C < 330
4A
200
330 C < 470
5A
300VDC and 375VDC
470 C < 470
7A
330 C < 330
4A
220
330 C < 470
5A
320VDC and 405VDC
470 C < 470
7A
330 C < 100
2A
400
100 C < 220
4A
500VDC and 600VDC
220 C < 470
7A
Printed with white color letter on black sleeve
Drawing
(BcoodtteomZBpolantley)
Polarity bar
Sleeve (P.E.T.)
L±²
Pressure relief vent
10±_0.1
10
4.0±0.5
0.8 ^+-00..12
0.8^+-00..21
2-2 f±^0.1
(PC board hole dimensions)
1.5 ^+-00..12
(Terminal dimensions)
Type numbering system (Example : 200V 680µF)
L¹ A² Q³ 2⁴ D⁵ 6⁶ 8⁷ 1⁸ M⁹ E^{10 1}L¹ A¹² 4^{13 1}0^{4 15 16}
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (680µF)
Rated voltage (200V)
Series name
Type
Case length code
Case dia. code
fD Code
22 Z
25 A
30 B
35 C
Please contact to us if other configurations are required.
Bottom Plate
ZB
code less
WPWBloaiittthhtteooBmuotPttolamte
Minimum order quantity : 50pcs.
Dimension table in next page.
CAT.8100V