F980E476MMA Datasheet, PDF (1/1 Pages) Nichicon corporation – SOLID TANTALUM ELECTROLYTIC CAPACITORS

SOLID TANTALUM ELECTROLYTIC CAPACITORS
F98 Resin-molded Chip,
High Capacitance Series
Adapted to the RoHS directive (2002/95/EC).
Specifications
Type numbering system (Example : 6.3V 10 µF)
123
F98
45
0J
678
106
9 10 11
MM
Taping code
(Refer to page 267 for details)
Case code
Capacitance tolerance
Rated Capacitance _{Rated voltage}
Series
Drawing
L
W1
H
W2
S1 S2 S1
(mm)
Cace Code L
W1
W2
H
S1
S2
M
1.6 ± 0.1 0.85 ± 0.1 0.65 ± 0.1 0.8 ± 0.1 0.5 ± 0.1 0.6 ± 0.1
S
2.0 ± 0.1 1.25 ± 0.1 0.9 ± 0.1 0.8 ± 0.1 0.5 ± 0.1 1.0 ± 0.1
Marking
J
Item
Performance Characteristics
Category
Temperature Range
--55 ~ +125°C (Rated temperature : 85°C)
Capacitance Tolerance ±20% (at 120Hz)
Dissipation Factor(120Hz) Refer to the list below (* 1)
ESR(100kHz)
Refer to the list below (* 1)
Leakage Current
After 5 minute's application of rated voltage, leakage current at
20°C is not more than 0.1CV or 0.5µA, whichever is greater.
Damp Heat
At 40°C, 90 ~ 95% R.H., For 500hours (No voltage applied)
Capacitance Change Refor to the list below (* 1)
Dissipation Factor
150% or less of initial specified value
Leakage Current
200% or less of initial specified value
Temperature Cycles
At --55°C / +125°C, For 30 minutes each, 5 cycles
Capacitance Change Refor to the list below (* 1)
Dissipation Factor
150% or less of initial specified value
Leakage Current
Initial specified value or less
Resistance to Soldering
Heat
At 260°C, For 10 seconds, Reflow,
Capacitance Change Refor to the list below (* 1)
Leakage Current
Initial specified value or less
Leakage Current
Initial specified value or less
Surge^∗
After application of surge in series with a 1kΩ resistor at the
rate of 30 seconds ON, 30 seconds OFF, for 1000 successive
test cycles at 85°C, capacitors meet the characteristics
requirements listed below.
Capacitance Change Refor to the list below (* 1)
Dissipation Factor
150% or less of initial specified value
Leakage Current
200% or less of initial specified value
Endurance∗
After 1000 hours' application of rated voltage in series with a
3Ω resistor at 85°C, capacitors meet the characteristic
requirements listed below
Capacitance Change Refor to the list below (* 1)
Dissipation Factor
150% or less of initial specified value
Leakage Current
200% or less of initial specified value
Shear Test
After applying the pressure load of 5N
for 10±1 seconds horizontally to the
center of capacitor side body which has
no electrode and has been soldered
beforehand on an aluminum substrate,
there shall be found neither exfoliation
nor its sign at the terminal electrode.
5N (0.51kg • f)
For 10 ± 1seconds
Terminal Strength
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor, the
pressure strength is applied with
a specified jig at the center of the _R230
20
substrate so that the substrate
may bend by 1mm as illustrated.
Then, there shall be found no
remarkable abnormality on the
45 45
capacitor terminals.
Rated voltage
(Voltage code)
∗ As for the surge and derated voltage at 125˚C, refer to page 266 for details.
Standard ratings
Rated Volt
(V)
Rated
Capacitance
(µF)
Case
code
Part Number
Leakage
Current
(µA)
Disspation
Factor
ESR _*1∆C/C
(%@120Hz) (Ω@100kHz) (%)
V 2.5
4
6.3
10
16
20
Cap.(µF)
Code
0E
0G
0J
1A
1C
1D
1
105
M
M
2.2
225
M
M
4.7
475
M
M
M
10
106
M
M
S
22
226
M
M
S
2.5
47
M F980E476MMA 1.2
30
22
M F980G226MMA 0.9
15
4
33
M F980G336MMA 1.3
30
68
S F980G686MSA 2.7
30
4.7
M F980J475MMA 0.5
20
10
M F980J106MMA 0.6
8
6.3
22
M F980J226MMA 1.4
20
4
± 30
7.5 ± 30
4
± 30
4
± 30
7.5 ± 30
6
± 30
6
± 30
33
336
M
(M)
S
47
S F980J476MSA 3.0
25
6
± 30
47
476
M
(M)
S
2.2
M F981A225MMA 0.5
6
7.5 ± 30
68
686
S
4.7
M F981A475MMA 0.5
6
6
± 30
100
107
(S)
(S)
10
10
M F981A106MMA 1.0
20
7.5 ± 30
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
22
S F981A226MSA 2.2
20
33
S F981A336MSA 3.3
30
1
M F981C105MMA 0.5
6
4
± 20
6
± 30
10 ± 30
16
2.2
M F981C225MMA 0.5
6
4.7
M F981C475MMA 0.8
12
10 ± 30
12 ± 30
10
S F981C106MSA 1.6
18
4
± 20
20
1
M F981D105MMA 0.5
6
10 ± 30
CAT.8100V