F950G156MPAAQ2_09 Datasheet, PDF (1/2 Pages) Nichicon corporation – SOLID TANTALUM ELECTROLYTIC CAPACITORS

SOLID TANTALUM ELECTROLYTIC CAPACITORS
F95 Conformal coated
Chip
Compliant to the RoHS directive (2002/95/EC).
Applications
Smartphone
Tablet PC
Wireless module
e-book
Type numbering system (Example : 35V 1.5µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
F 9 5 1 V 1 5 5 M A AQ2
Single face electrode
Taping code
(Refer to page 323 for details)
Case code
Capacitance tolerance
Rated capacitance _{Rated voltage}
Series
Drawing
L
W
H
Resin
Solder electrode
Solder electrode
A B C ^(D)
Single-side electrodes
(Both electrodes at bottom side only)
Dimensions
Case code L
W
H
A
R
2.2 ± 0.3 1.25 ± 0.3 0.65MAX. 0.6 ± 0.3
P
2.2 ± 0.3 1.25 ± 0.3 1.0 ± 0.2 0.6 ± 0.3
Q
3.2 ± 0.2 1.6 ± 0.2 0.8 ± 0.2 0.8 ± 0.2
S
3.2 ± 0.3 1.6 ± 0.3 1.0 ± 0.2 0.8 ± 0.3
A
3.2 ± 0.3 1.7 ± 0.3 1.4 ± 0.2 0.8 ± 0.3
T
3.5 ± 0.2 2.7 ± 0.2 1.0 ± 0.2 0.8 ± 0.2
B
3.5 ± 0.2 2.8 ± 0.2 1.8 ± 0.2 0.8 ± 0.3
D dimension only for reference
B
0.8 ± 0.3
0.8 ± 0.3
1.2 ± 0.2
1.2 ± 0.3
1.2 ± 0.3
1.2 ± 0.2
1.2 ± 0.3
C
0.5MIN
0.8 ± 0.3
0.8 ± 0.2
0.8 ± 0.3
0.8 ± 0.3
1.1 ± 0.2
1.1 ± 0.3
(mm)
(D)
(0.2)
(0.2)
(0.2)
(0.2)
(0.2)
(0.2)
(0.2)
Specifications
Item
Per formance Characteristics
Category
Temperature Range
--55 to +125˚C (Rated temperature : 85˚C)
Capacitance Tolerance ± 20%, ± 10% (at 120Hz) (However P Case ± 20%)
Dissipation Factor
(at 120Hz)
Refer to next page
ESR(100kHz) Refer to next page
Leakage Current
Refer to next page
Provided that
• After 1 minute's application of rated voltage, leakage current at 85˚C,
10 times or less than 20˚C specified value.
• After 1 minute's application of rated voltage, leakage current at 125˚C,
12.5 times or less than 20˚C specified value.
Capacitance Change ^{+15% Max. (at +125˚C)}
by Temperature
+10% Max. (at + 85˚C)
--10% Max. (at --55˚C)
Damp Heat
(Steady State)
At 40˚C, 90 to 95% R.H., For 500 hours (No voltage applied)
Capacitance Change • • • • • • Refer to next page (∗ 1)
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
Temperature Cycles
At --55˚C / +125˚C, 30 minutes each, For 5 cycles,
Capacitance Change • • • • • • Refer to next page (∗ 1)
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • •• Initial specified value or less
Resistance to
Soldering Heat
10 seconds reflow at 260˚C, 10 seconds immersion at 260˚C
Capacitance Change • • • • • • Refer to next page (∗ 1)
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • •• Initial specified value or less
Surge^∗
Endurance∗
Shear Test
Terminal Strength
After application of surge voltage in series with a 33Ω resistor at the rate of 30
seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85˚C,
capacitors meet the characteristics requirements listed below.
Capacitance Change • • • • • • Refer to next page (∗ 1)
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
After 2000 hours' application of rated voltage at 85˚C,
capacitors meet the characteristic requirements listed below.
Capacitance Change • • • • • • Refer to next page (∗ 1)
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • •• Initial specified value or less
After applying the pressure load of 5N
for 10 ± 1 seconds horizontally to the
center of capacitor side body which has
no electrode and has been soldered
beforehand on a substrate, there shall be
found neither exfoliation
nor its sign at the terminal electrode.
5N (0.51kg • f)
For 10 ± 1 seconds
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor,
the pressure strength is applied with
a specified jig at the center of the
R230
20
substrate so that the substrate may
bend by 1mm as illustrated. Then,
there shall be found no remarkable
45
45
abnormality on the capacitor terminals.
∗ As for the surge voltage, refer to page 322 for details.
Standard Ratings
Cap.
V
4
(µF)
Code
0G
1
105
1.5
155
2.2
225
3.3
335
4.7
475
6.8
685
10
106
15
156
P
22
226
P
33
336
P
47
476
(R) ^• P ^• Q ^• S ^• A
68
686
S^•A
100
107
P^•Q^•S^•A
150
157
P^•B
220
227
(P) ^• Q ^• S ^• A ^• T ^• B
330
337
(P) ^• (S) ^• A ^• T^• B
470
477
(P) ^• (A) ^• (T) ^• B
680
687
(T)
6.3
0J
P
P
R^•P
(R) ^• P ^• Q ^• S ^• A
P^•Q^•S^•A
P^•S^•A
P^•Q ^•S^•A^•T^•B
B
(S) ^• (A) ^• (T) ^• B
B
(B)
10
1A
P
P
P
R^•P
P
P^•Q^•S^•A
P^•Q^•S^•A
(P) ^•(Q) ^•S^•A^•T^•B
B
(S) ^• A ^• T ^• B
16
1C
P
P
P
P
R^•P
P^•Q^•S^•A
S^•A
Q^•S^•A^•T^•B
(A) ^• T ^• B
B
20
1D
P^•S
A
S^•A
Q^•A
S^•A^•B
B
25
1E
R^•P^•S
S
R^•P^•S^•A
A
P^•Q^•S^•A
(Q) ^• (S)
A ^• (T) ^• B
35
1V
P^•S^•A
A
(S) ^• A
(S) ^• (A) ^• B
(T) ^• B
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
CAT.8100A