F721A477MMC Datasheet, PDF (1/2 Pages) Nichicon corporation – SOLID TANTALUM ELECTROLYTIC CAPACITORS

SOLID TANTALUM ELECTROLYTIC CAPACITORS
F72 Low Profile
Conformal
coated Chip
F75 Maximum CV
Conformal
coated Chip
Compliant to the RoHS directive (2002/95/EC).
Specifications
Item
Per formance Characteristics
Category
Temperature Range
--55 to + 125˚C (Rated temperature : + 85˚C)
Capacitance Tolerance ± 20%, ± 10% (at 120Hz)
Dissipation Factor
Refer to next page
(120Hz)
ESR (100kHz) Refer to next page
Leakage Current
• After 1 minute's application of rated voltage, leakage current at 20˚C is not
more than 0.01CV or 0.5µA, whichever is greater.
• After 1 minute's application of rated voltage, leakage current at 85˚C is not
more than 0.1CV or 5µA, whichever is greater.
• After 1 minute's application of derated voltage, leakage current at 125˚C is
not more than 0.125CV or 6.3µA, whichever is greater.
Applications
Wireless modem
Tablet PC
e-book
SSD
Smart meter
F72
Type numbering system (Example : 10V 100µF)
1 2 3 4 5 6 7 8 9 10 11
F72 1A 107 M R
12 13 14
AQ 2
Single face electrode
Taping code(Refer to page 333 for details)
Case code
Capacitance tolerance
Rated capacitance _{Rated voltage}
Series
Drawing
H
A
B
D
L
W
Dimensions
Solder electrode
(mm)
Case code L
W
H
A
B
(D)
R 7.2 ± 0.3 6.0 ± 0.3 1.2 ± 0.3 1.3 ± 0.4 3.8 ± 0.6 (6.2)
M 7.2 ± 0.3 6.0 ± 0.3 2.0MAX. 1.3 ± 0.4 3.8 ± 0.6 (6.2)
F75
D dimension only for reference
Type numbering system (Example : 16V 150µF)
1 2 3 4 5 6 7 8 9 10 11
F75 1C 157 M D
12 13 14
AQ 2
Single face electrode
Taping code(Refer to page 333 for details)
Case code
Capacitance tolerance
Rated capacitance _{Rated voltage}
Series
Drawing
H
A
B
D
L
Capacitance Change ^{+15% Max. (at +125˚C)}
+10% Max. (at +85˚C)
by Temperature
--10% Max. (at --55˚C)
Damp Heat
(Steady State)
At 40˚C, 90 to 95% R.H., For 500 hours (No voltage applied)
Capacitance Change • • • • • • Refer to * 1
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • Initial specified value or less
Temperature Cycles
At --55˚C / +125˚C, 30 minutes each, For 5 cycles,
Capacitance Change • • • • • • Refer to * 1
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Currentv • • • • • • • • • • Initial specified value or less
Resistance to
Soldering Heat
10 seconds reflow at 260˚C, 10 seconds immersion at 260˚C
Capacitance Change • • • • • • Refer to * 1
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
Surge^∗
After application of surge in series with a 33Ω resistor at the rate of 30
seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85˚C,
capacitors shall meet the characteristic requirements table below.
Capacitance Change • • • • • • Refer to * 1
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
Endurance^∗
After 2000 hours' application of rated voltage at 85˚C,
capacitors shall meet the characteristic requirements table below.
Capacitance Change • • • • • • Refer to * 1
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
Shear Test
After applying the pressure load of 5N
for 10±1 seconds horizontally to the
center of capacitor side body which has
no electrode and has been soldered
beforehand on a substrate, there shall be
found neither exfoliation
nor its sign at the terminal electrode.
5N (0.51kg • f)
For 10 ± 1 seconds
Terminal Strength
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of capacitor,
the pressure strength is applied with
a specified jig at the center of
R230
substrate so that the substrate may
bend by 1mm as illustrated. Then,
there shall be found no remarkable
45
abnormality on the capacitor terminals.
20
45
∗ As for the surge voltage, refer to page 332 for details.
Dimensions
Case code L
W
H
A
B
U 7.1 ± 0.3 3.2 ± 0.3 2.0MAX. 1.3 ± 0.3 3.6 ± 0.6
C 7.1 ± 0.3 3.2 ± 0.3 2.5 ± 0.3 1.3 ± 0.3 3.6 ± 0.6
(mm)
(D)
(6.0)
(6.0)
D 7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3 1.3 ± 0.4 3.9 ± 0.6 (6.4)
W
R 7.2 ± 0.3 6.0 ± 0.3 3.5 ± 0.3 1.3 ± 0.4 3.8 ± 0.6 (6.2)
Standard Ratings
D dimension only for reference
F72
V
4
6.3
10
16
Cap.(µF)
Code
0G
0J
1A
1C
033
336
R
047
476
R
R
068
686
R
R
R
F75
Cap. (µF)
V
4
Code
0G
068
686
100
107
150
157
220
227
6.3
10
16
0J
1A
1C
C
C
C
D
C
C•D
R
100
107
R
R
R
330
337
C
C•D
D
150
157
R
220
227
R
330
337
R
R
R
470
477
C•D
U•D
U•R
680
687
D (U) • D • R
R
R
( ) The series in parentheses
1000
108
D • R (U) • R
R
(R)
are being developed. Please
1500
158
R
470
477
680
687
M
contact to your local Nichicon
2200
228
R
sales office when these
M
series are being designed in
1000
108
M
M
your application.
1500
158
M
CAT.8100B