NSPVM Datasheet, PDF (1/3 Pages) NIC-Components Corp. – Solid Polymer Aluminum Electrolytic Capacitors

Solid Polymer Aluminum Electrolytic Capacitors NSPVM Series
SUPER LOW ESR, WIDE TEMPERATURE, SURFACE MOUNT, POLARIZED
FEATURES
• ULTRA LOW ESR (TO 13mΩ)
* NEW *
• HIGH RIPPLE CURRENT RATINGS
• REDUCED SIZES (LOW PROFILE)
Low ESR &
High Ripple Current
CHARACTERISTICS
Rated Voltage Range
2.5 ~ 35VDC
Capacitance Range
10 ~ 1,200μF
Operating Temperature Range
-55°C ~ +105°C
Capacitance Tolerance
±20% (M)
Maximum Leakage Current
After 2 minutes
2.5V ~ 20V = 0.2CV
25V ~ 35V = 0.5CV
W.V. (Vdc)
2.5
4.0
6.3
10
16
20
25
35
Max. Tan δ at 120Hz/20°C
S.V. (Vdc)
2.9
4.6
7.2
11.5
18
23
28.7
40
Tan δ
0.12 max.
Low Temperature Stability Z-55°C/Z+20°C
Impedance Ratio @ 120Hz Z+105°C/Z+20°C
<1.15
<1.25
Duration
All Case Sizes: 2,000 hours
Load Life Test
@ 105°C
Δ Capacitance
Δ Tan δ
Δ ESR
Within ±20% of initial measured value
Less than 150% of specified value
Less than 150% of specified value
Δ LC
Less than specified value
The following specifications shall be satisfied when the capacitors are restored to +20°C after
subjecting them to the DC rated voltage at +60°C, 90% ~ 95% RH for 500 hours.
Appearance
No significant damage
Damp Heat
Δ Capacitance
Within ±20% of initial measured value
Δ Tan δ
Less than 150% of specified value
Δ ESR
Less than 150% of specified value
Δ LC
Less than specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the specified surge
voltage @ +105°C for 30 seconds through a protective resistor (1K ohm) and discharged for 5 minutes,
30 seconds.
Surge Voltage
Appearance
Δ Capacitance
No significant damage
Within ±20% of initial measured value
Δ Tan δ
Less than 150% of specified value
Δ ESR
Less than 150% of specified value
Δ LC
Less than specified value
Failure Rate
0.5% per 1,000 hours maximum (Confidence level 60% @ +105°C)
PART NUMBER SYSTEM
NSPVM 391 M 2.5V 6.3X6 L LB F .
RoHS Compliant
Sn-Bi Finish, 15" Reel
Peak Reflow Temperature: L = +250°C, J = +240°C
Case Size (DφxL)
Working Voltage (Vdc)
Tolerance Code (M=20%)
Capacitance Code: First 2 characters
significant, third character is multiplier
Series
PEAK REFLOW SOLDERING CODE
Code
L
J
Peak Reflow Temperature
+250°C
+240°C
TERMINATION/PACKAGING CODE
Code Termination Finish and Reel Size
LB
Sn-Bi Finish, 15" reel
PRECAUTIONS
Please review the notes on correct use, safety and precautions found on
pages T10 & T11 of NIC’s Electrolytic Capacitor catalog.
Also found at www.niccomp.com/precautions
If in doubt or uncertainty, please review your specific application - process
details with NIC’s technical support personnel: [e-mail]
NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com
SPECIFICATIONS ARE SUBJECT TO CHANGE
1