USB-6008 Datasheet, PDF (4/5 Pages) National Instruments Corporation – 8 analog inputs at 12 or 14 bits,up to 48 kS/s

Low-Cost, Bus-Powered Multifunction DAQ for USB – 12- or 14-Bit, up to 48 kS/s, 8 Analog Inputs
Physical Characteristics
If you need to clean the module, wipe it with a dry towel.
Dimensions (without connectors) ....... 6.35 by 8.51 by 2.31 cm
(2.50 by 3.35 by 0.91 in.)
Dimensions (with connectors) ............ 8.18 by 8.51 by 2.31 cm
(3.22 by 3.35 by 0.91 in.)
Weight (without connectors) .............. 59 g (2.1 oz)
Weight (with connectors) ................... 84 g (3 oz)
I/O connectors..................................... USB series B receptacle
(2) 16-position (screw-terminal)
plug headers
Screw-terminal wiring ........................ 16 to 28 AWG
Screw-terminal torque........................ 0.22 to 0.25 N•m
(2.0 to 2.2 lb•in.)
Power Requirement
USB (4.10 to 5.25 VDC).......................
USB suspend.......................................
80 mA typical
500 mA maximum
300 µA typical
500 µA maximum
Environmental
The USB-6008 and USB-6009 are intended for indoor use only.
Operating environment
Ambient temperature range ........... 0 to 55 °C (tested in accordance
with IEC-60068-2-1
and IEC-60068-2-2)
Relative humidity range ................. 10 to 90%, noncondensing
(tested in accordance
with IEC-60068-2-56)
Storage environment
Ambient temperature range ........... -40 to 85 °C (tested in
accordance with IEC-60068-2-1
and IEC-60068-2-2)
Relative humidity range ................. 5 to 90%, noncondensing
(tested in accordance
with IEC-60068-2-56)
Maximum altitude............................... 2,000 m
(at 25 °C ambient temperature)
Pollution degree.................................. 2
Safety and Compliance
Safety
This product is designed to meet the requirements of the following
standards of safety for electrical equipment for measurement, control,
and laboratory use:
• IEC 61010-1, EN 61010-1
• UL 61010-1, CSA 61010-1
Note: For UL and other safety certifications, refer to the product label
or visit ni.com/certification, search by model number or product line,
and click the appropriate link in the Certification column.
Electromagnetic Compatibility
This product is designed to meet the requirements of the following
standards of EMC for electrical equipment for measurement, control,
and laboratory use:
• EN 61326 EMC requirements; Minimum Immunity
• EN 55011 Emissions; Group 1, Class A
• CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A
Note: For EMC compliance, operate this device according to
product documentation.
CE Compliance
This product meets the essential requirements of applicable European
Directives, as amended for CE marking, as follows:
• 2006/95/EC; Low-Voltage Directive (safety)
• 2004/108/EC; Electromagnetic Compatibility Directive (EMC)
Note: Refer to the Declaration of Conformity (DoC) for this product for
any additional regulatory compliance information. To obtain the DoC for
this product, visit ni.com/certification, search by model number or
product line, and click the appropriate link in the Certification column.
Waste Electrical and Electronic Equipment (WEEE)
EU Customers: At the end of their life cycle, all products must be
sent to a WEEE recycling center. For more information about WEEE
recycling centers and National Instruments WEEE initiatives, visit
ni.com/environment/weee.htm.
BUY ONLINE at ni.com or CALL 800 813 3693 (U.S.)
4