PXI-4110 Datasheet, PDF (3/5 Pages) National Instruments Corporation – 3 independent DC power supplies/16-bit voltage setpoint and current limit

Triple-Output Programmable DC Power Supply
Specifications
Specifications subject to change without notice. For the most current and
complete specifcations, visit ni.com/modularinstruments.
Supply Characteristics
Number of channels............................ 3
DC Specifications
DC Current (Power)
Auxiliary Power
Internal Power
Channel DC Voltage Isolation¹ 20 mA Range 1 A Range 20 mA Range 1 A Range
0 0 to +6 V
N/A
N/A 1 A (6 W) N/A
1 A (6 W)
1 0 to +20 V 60 VDC, CAT I 20 mA 1 A (20 W) 20 mA 100 mA (2 W)²
2 0 to -20 V 60 VDC, CAT I 20 mA 1 A (20 W) 20 mA 100 mA (2 W)²
1_{Channels 1 and 2 are isolated from ground but not from each other.}
2_{Combined total power for channels 1 and 2 using internal power cannot exceed 3 W.}
Voltage Programming Accuracy/Resolution
Channels Range (V) Resolution (mV)
0
+6
0.12
1
+20
0.40
2
-20
0.40
Tempco = temperature coefficient
Accuracy ±(% of output + offset)
1-Year 13 to 33 °C Tempco/°C 0 to 55 °C
0.05 + 4 mV
0.005 + 0.3 mV
0.05 + 10 mV
0.005 + 1 mV
0.05 + 10 mV
0.005 + 1 mV
Current Programming Accuracy/Resolution³
Accuracy ±(% of output + offset)
Channels Range⁴
Resolution 1-Year 13 to 33 °C Tempco/°C 0 to 55 °C
0
1A
0.02 mA
0.15 + 4 mA
0.02 + 0.2 mA
1 and 2 20 mA
0.40 µA
0.15 + 60 µA
0.01 + 3 µA
1A
0.02 mA
0.15 + 4 mA
0.02 + 0.2 mA
Tempco = temperature coefficient
3_{Applies for current settings greater than 2% of range.}
4_{Minimum programmable current limit is 2% of range.}
Voltage Readback Accuracy/Resolution
Channels Range (V) Resolution (mV)
0
+6
0.06
1
+20
0.20
2
-20
0.20
Tempco = temperature coefficient
Accuracy ±(% of output + offset)
1-Year 13 to 33 °C Tempco/°C 0 to 55 °C
0.05 + 4 mV
0.005 + 0.2 mV
0.05 + 5 mV
0.005 + 0.5 mV
0.05 + 5 mV
0.005 + 0.5 mV
Current Readback Accuracy/Resolution⁵
Channels Range
Resolution
0
1A
0.01 mA
1 and 2 20 mA
0.20 µA
1A
0.01 mA
Tempco = temperature coefficient
5_{Applies for current outputs up to 500 mA.}
Accuracy ±(% of output + offset)
1-Year 13 to 33 °C Tempco/°C 0 to 55 °C
0.15 + 4 mA
0.02 + 0.2 mA
0.15 + 35 µA
0.01 + 3 µA
0.15 + 4 mA
0.02 + 0.2 mA
Ripple and Noise
Channels RMS Normal-Mode Voltage⁶
RMS Normal-Mode Current⁷
(20 mA into 500 Ω load)
0
<1.5 mV
<8 µA
1 and 2
<1.0 mV
<8 µA (<3 µA for 20 mA range)
6_{From 20 Hz to 20 MHz.} 7_{Current noise bandwidth is limited to 10 kHz for 1 A range and 400 Hz for 20 mA range.}
Voltage Output Speed⁸
Auxiliary Power
Internal Power
Rise Time⁹
Fall Time¹⁰
Rise Time⁹
Fall Time¹⁰
Channels Full Load No Load Full Load No Load Full Load No Load Full Load No Load
0
<1 ms <1 ms <1 ms <25 ms
Same as auxiliary power
1 and 2 <1 ms <1 ms <2 ms <56 ms <20 ms <10 ms <15 ms <56 ms
8_{Current limit set to 1 A for auxiliary power or 100 mA for internal power. For 20 mA range,}
all voltage output speeds are <80 ms.
9_{Rise time is from 10 to 90% of programmed voltage change at maximum current.}
10_{Fall time is from 90 to 10% of programmed voltage change at maximum current.}
Line and Load Regulation
Line Regulation¹¹
±(% of output + offset)
Channels
0
1 and 2
Voltage
N/A
0.01 + 1 mV
Current
N/A
0.01 + 0.02% of range
11_{Per volt change in auxiliary input.}
Load Regulation
±(% of range selected)
Voltage (per A Current (per V
of output load) of output load)
0.42
0.02
0.1
0.007 (0.003 for
20 mA range)
General Specifications
Sampling rate
Default ............................................
Maximum ........................................
Warm-up .............................................
I/O connectors
Supply channels..............................
External power................................
Dimensions..........................................
Auxiliary power (optional)...................
300 S/s (10 samples averaged)
3000 S/s
15 minutes
6-pos COMBICON (3.81 mm)
2-pos COMBICON (3.5 mm)
13.1 by 21.6 cm (5.1 by 8.5 in.)
Single PXI slot, 3U
11 to 15.5 VDC, 5 A max
Environment
Operating temperature .......................
Storage temperature...........................
Relative humidity ................................
Pollution degree..................................
Approved altitude ..............................
0 to 55 °C
-20 to 70 °C
5 to 85% noncondensing
2
up to 2000 m
Safety
This product is designed to meet the requirements of the following
standards of safety for electrical equipment for measurement, control,
and laboratory use:
• IEC 61010-1, EN 61010-1
• UL 61010-1, CSA 61010-1
For UL and other safety certifications, refer to the product label, or visit
ni.com/certification, search by model number or product line, and click
the appropriate link in the Certification column.
Electromagnetic Compatibility
• CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A
• EN 55011 Emissions; Group 1, Class A
• EN 61326 EMC requirements; Minimum Immunity
For EMC compliance, operate this device according to product documentation.
BUY ONLINE at ni.com or CALL 800 813 3693 (U.S.)
3