TQ-SMD Datasheet, PDF (1/5 Pages) Nais(Matsushita Electric Works) – LOW-PROFILE SURFACE-MOUNT RELAY

LOW-PROFILE
SURFACE-MOUNT RELAY
TESTING
TQ-SMD
RELAYS
FEATURES
14
.551
9
.354
5.6
.220
• Low-profile: 6 mm .236 inch in height comforming to EIA standards
(Tape height: max. 6.5 mm .256 inch )
• Tape and reel package is available as standard packing style
• Surge withstand between contacts and coil: 2,500 V
• Breakdown voltage between contacts and coil: 1,500 V
• High capacity: 2 A
mm inch
• High sensitivity:
2 Form C; 140 mW power consumption (Single side stable type)
SPECIFICATIONS
Contact
Arrangement
2 Form C
Initial contact resistance, max.
(By voltage drop 6 V DC 1 A)
75 mΩ
Contact material
Gold-clad silver alloy
Nominal switching capacity
(resistive load)
2 A 30 V DC,
0.5 A 125 V AC
Rating
Max. switching power
(resistive load)
Max. switching voltage
60 W, 62.5 VA
220 V DC, 125 V AC
Max. switching current
Min. switching capacity f1
2A
10 µA 10 mV DC
Nominal
operating
power
Single side stable
1 coil latching
140 mW (1.5 to 12 V DC)
200 mW (24 V DC)
300 mW (48 V DC)
70 mW (1.5 to 12 V DC)
100 mW (24 V DC)
2 coil latching
140 mW (1.5 to 12 V DC)
200 mW (24 V DC)
Mechanical (at 180 cpm)
10 ⁸
Expected
life (min.
operations)
Electrical
(at 20 cpm)
2 A 30 V DC
resistive
1 A 30 V DC
resistive
10⁵
2×10⁵
0.5 A 125 V AC
resistive
10⁵
Note:
f1This value can change due to the switching frequency, environmental conditions,
and desired reliability level, therefore it is recommended to check this with the ac-
tual load.
Remarks
* Specifications will vary with foreign standards certification ratings.
*¹ Measurement at same location as "Initial breakdown voltage" section.
*² By resistive method, nominal voltage applied to the coil; contact carrying current:
2 A.
*³ Nominal voltage applied to the coil, excluding contact bounce time.
*⁴ Nominal voltage applied to the coil, excluding contact bounce time without diode.
*⁵ Half-wave pulse of sine wave: 6 ms; detection time: 10 µs
*⁶ Half-wave pulse of sine wave: 6 ms
*⁷ Detection time: 10 µs
*⁸ Refer to 4. Conditions for operation, transport and storage mentioned in Cautions
for use (Page 178).
Characteristics
Initial insulation resistance*¹
Initial
breakdown
voltage
Between open
contacts
Between contact sets
Between contact and
coil
Initial surge
voltage
Between open
contacts
(10×160 µs)
Between contacts and
coil (2×10 µs)
Temperature rise*² (at 20°C)
Operate time [Set time]*³ (at 20°C)
Release time [Reset time]*⁴
(at 20°C)
Shock resistance
Functional* ⁵
Destructive*⁶
Functional* ⁷
Vibration resistance
Destructive
Conditions for oper-
ation, transport and
storage*⁸ (Not freez-
ing and condensing
at low temperature)
Ambient
temperature
Humidity
Unit weight
Min. 1,000 MΩ (at 500 V DC)
1,000 Vrms for 1 min.
(Detection current: 10 mA)
1,500 Vrms for 1 min.
(Detection current: 10 mA)
1,500 Vrms for 1 min.
(Detection current: 10 mA)
1,500 V (FCC Part 68)
2,500 V (Bellcore)
Max. 50°C
Max. 4 ms (Approx. 2 ms)
[Max. 4 ms (Approx. 2 ms)]
Max. 4 ms (Approx. 1 ms)
[Max. 4 ms (Approx. 2 ms)]
Min. 750 m/s² {75 G}
Min. 1,000 m/s² {100 G}
200 m/s² {20G}, 10 to 55 Hz
at double amplitude of 3.3 mm
294 m/s² {30G}, 10 to 55 Hz
at double amplitude of 5 mm
–40°C to +85°C*³
–40°F to +185°F
5 to 85% R.H.
Approx. 2 g .071 oz
140