TN2-3V Datasheet, PDF (1/4 Pages) Nais(Matsushita Electric Works) – SLIM POLARIZED RELAY

TN-RELAYS ^{SLIM POLARIZED RELAY}
5.6
14
.220
.551
9.8
.386
FEATURES
• Small size for minimal PC board
mounting requirements
• Small header area makes higher den-
sity mounting possible
• Surge voltage withstand: 1500 V FCC
Part 68
• Sealed construction allows automatic
cleaning
mm inch
• High sensitivity: 140 mW nominal op-
erating power (single side stable 3-12
V type)
• Self-clinching terminal also available
SPECIFICATIONS
Contact
Arrangement
2 Form C
Initial contact resistance, max.
(By voltage drop 6 V DC 1A)
60 mΩ
Contact material
Gold-clad silver
Nominal switching capacity
(resistive load)
1 A 30 V DC,
0.5 A 125 V AC
Rating
Max. switching power
(resistive load)
Max. switching voltage
30 W, 62.5 VA
110 V DC,125 V AC
Max. switching current
Min. switching capacity f1
1A
10 µA 10 mV DC
Nominal
operating
power
Single side stable
1 coil latching
140 mW (3 to 12 V DC)
200 mW (24 V DC)
300 mW (48 V DC)
100 mW (3 to 12 V DC)
150 mW (24 V DC)
2 coil latching
200 mW (3 to 12 V DC)
300 mW (24 V DC)
Mechanical (at 180 cpm)
10 ⁸
Expected
life (min.
operations)
Electrical
(at 20 cpm)
1 A 30 V DC
resistive load
0.5 A 125 V AC
resistive load
2 × 10⁵
10⁵
Note:
f1This value can change due to the switching frequency, environmental conditions,
and desired reliability level, therefore it is recommended to check this with the ac-
tual load.
Remarks
* Specifications will vary with foreign standards certification ratings.
*¹ Measurement at same location as "Initial breakdown voltage" section.
*² By resistive method, nominal voltage applied to the coil; contact carrying current:
1 A.
*³ Nominal voltage applied to the coil, excluding contact bounce time.
*⁴ Nominal voltage applied to the coil, excluding contact bounce time without diode.
Characteristics
Initial insulation resistance*¹
Initial
breakdown
voltage
Between open
contacts
Between contact and
coil
Between contact sets
FCC surge voltage between open
contacts
Temperature rise*² (at 20°C)
Operate time [Set time]*³ (at 20°C)
Release time [Reset time]*⁴
(at 20°C)
Shock resistance
Functional* ⁵
Destructive*⁶
Functional* ⁷
Vibration resistance
Destructive
Conditions for oper-
ation, transport and
storage* ⁸
(Not freezing and
condensing at low
temperature)
Unit weight
Ambient
temperature
Humidity
Min. 1,000 MΩ (at 500 V DC)
750 Vrms for 1 min.
(Detection current: 10 mA)
1,000 Vrms for 1 min.
(Detection current: 10 mA)
1,000 Vrms for 1 min.
(Detection current: 10 mA)
1,500 V
Max. 50°C
Max. 3 ms (Approx. 2 ms)
[Max. 3 ms (Approx. 2 ms)]
Max. 3 ms (Approx. 1 ms)
[Max. 3 ms (Approx. 2 ms)]
Min. 490 m/s² {50G}
Min. 980 m/s² {100G}
176.4 m/s² {18G}, 10 to 55 Hz
at double amplitude of 3 mm
294 m/s² {30G}, 10 to 55 Hz
at double amplitude of 5 mm
–40°C to +70°C
–40°F to +158°F
5 to 85% R.H.
Approx. 1.5 g .053 oz
*⁵ Half-wave pulse of sine wave: 11 ms; detection time: 10 µs.
*⁶ Half-wave pulse of sine wave: 6 ms.
*⁷ Detection time: 10 µs.
*⁸ Refer to 4. Conditions for operation, transport and storage mentioned in Cautions
for use (Page 178).
ORDERING INFORMATION
Ex. TN 2
L2
H
12V
Contact arrangement Operating function
Terminal shape
Coil voltage(DC)
2: 2 Form C
Nil: Single side stable Nil: Standard PC board terminal
L: 1 coil latching
H: Self-clinching terminal
L2: 2 coil latching
3,4.5,5,6,9,12,
24,48*V
*48 V coil type: Single side stable only
Note: AgPd stationary contact types available for high resistance against contact sticking.
When ordering, please add suffix “–3” like TN2–12V–3.
150