FR05CM21AR Datasheet, PDF (7/8 Pages) Murata Manufacturing Co., Ltd. – Rotary Sensors

!Note •PPleleaasseerreeaaddrraatitninggaanndd!!CCAAUUTTIOIONN((foforrsstotorraaggeeaannddooppeerraatitningg,,rraatitningg,,ssooldldeerrininggaannddmmoouunntitningg,,hhaannddlilningg))ininththisisPcDatFalcoagtatolopgrteovepnretvsemnot ksimngokaindg/oarndb/uorrnbinugr,neintgc., etc.
S35E2.pdf 02.5.21
•TThhisisccaatatalologghhaassoonnlylytytyppicicaal lssppeeccififciacatiotionns.sTbheecraeufosree,thyeorue aisrenroesqpuaecsetefdortodaeptapilreodvespoeucripficroadtiuocntss.pTehceifriecafotiroen, polretaosteraanpsparcotvteheouarpprodvaulcst hsepetcfifoicraptrionduocrt tsrapnescaificctatihoen abpepfororevaolrdsehreinegt .for product specification before ordering.
!Caution/Notice
s !Caution (Handling)
1. This sensor generates very strong suction because
the sensor contains a permanent magnet. Be careful
of handling the sensor not to apply mechanical
shock.
2. Because this sensor contains a permanent magnet, it
could damage magnetic signal in the writable
magnetic card such as train ticket and pre-paid
card. Please consult with us before applying it in
such circumstances.
3. Do not approach the sensor to the person who is
with an electronic medical device. It is very
dengerous by miss operation of an electronic
medical device.
s Notice (Storage and Operating Condition)
1. Please do not apply mechanical shock or pressure on
environment, please consult with us.
4
the sensing surface because it leads to change in
3. Please do not apply excessive force to the terminal,
the output level or destruction of magnetoresistive
not to rotate nor to bend.
element.
4. Please do not pull the lead by excessive force, not
2. Please do not use or keep the sensor in the
to rotate, not to bend.
corrosive gas (Chlorine gas, Nitric oxie gas,
5. Please avoid the airborne particles.
Sulfuric acid gas, and so on). Metal case might be
6. Please avoid the strong vibraion and shock.
corroded due to it. Some of our sensor is made with
7. Ambient temperature change should be within
stainless steal case for better resistance to
1 degrees C/min.
corrosion. If the sensor should be used in such an
s Notice (Soldering and Mounting)
1. Wiring should be avoided while supply voltage is
applied.
2. Do not place the sensor near high voltage lines or
high current lines.
3. Please avoid placing magnetic material or magnetic
field generator other than the detected object
near to the sensor. It could cause change in the
output level, resulting in malfunction of the
finished goods.
4. Hand soldering should be applied. Soldering should
be done in following condition;
Soldering temperature:
350+/-10 degrees C less than 3 seconds or
260+/-5 degrees C less than 10 seconds.
5. Flux should be rosin flux and its chlorine content
should be no more than 0.2wt%.
6. Flux cleaning should be done by hand brushing.
7. Prevent the flux cleaning solvent from splashing on
the sensor.
( ) o Part Numbering
The structure of the "Global Part Numbers" that have been adopted since June 2001 and the meaning of each code are described herein.
If you have any questions about details, inquire at your usual Murata sales office or distributor.
Rotary Sensors
(Global Part Number) FR 05CM 12AL
qw
er
qProduct ID
wType
eCharacteristics
rIndividual Specification Code
* Global Part Number shows only an example which might be different
from actual part number.
* Any other definitions than "qProduct ID" might have different digit
number from actual Global Part Number.
7