DE2B3KY331KA3BM02 Datasheet, PDF (49/72 Pages) Murata Manufacturing Co., Ltd. – Safety Certified Ceramic Capacitors/ High Voltage Ceramic Capacitors

C85E.pdf !Note • Th!is PNDoFteca•taPlolegasisedroewadnlroaatdinegdafnrodm!thCeAwUeTbIOsiNte(ofof rMsutoraratageM, aonpuefraactitnugri,nrgatcinog.,,ltsdo.ldTehreinregf,omreo,uint’tsinsgpaencdifichaatniodnlisnga)reinstuhbisjeccatttaolocghatongpereovreonut rsmprookdiuncgtsanind/iot rmbauyrnbiengd,isectco.ntinued without advance notice. Please check with our
sales repres_•en_Tt_ha_istiv_ce_as_tao_lor _gpr_ho_ad_suc_ot_ne_lyn_tg_yi_pn_ie_ce_ar_ls_spb_ee_cfo_ifr_ice_ao_tir_od_ne_sri_bn_eg_c. _{ause there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
08.10.29 ^{• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
DEB Series Specifications and Test Methods
No.
Item
Specifications
Test Method
1 Operating Temperature Range
-25 to +85°C
2 Appearance and Dimensions
No marked defect on appearance form
and dimensions are within specified
range.
The capacitor should be visually inspected for evidence of
defect. Dimensions should be measured with slide calipers.
3 Marking
To be easily legible
The capacitor should be visually inspected.
Between Lead
Wires
No failure
The capacitor should not be damaged when DC voltage of
200% of the rated voltage is applied between the lead wires for
1 to 5 sec. (Charge/Discharge currentV50mA)
4
Dielectric
Strength
Body Insulation
No failure
The capacitor is placed in the container
with metal balls of diameter 1mm so that
each lead wire, short circuited, is kept
about 2mm off the metal balls as shown in
the figure at right, and DC voltage of 1.3kV
is applied for 1 to 5 sec. between capacitor
lead wires and metal balls.
(Charge/Discharge currentV50mA)
About 2mm
Metal balls
5
Insulation
Resistance (I.R.)
Between Lead
Wires
10000MΩ min.
The insulation resistance should be measured with
DC500±50V within 60±5 sec. of charging.
6 Capacitance
Within specified tolerance
The capacitance should be measured at 20°C with 1±0.2kHz
and AC5V(r.m.s.) max.
7 Dissipation Factor (D.F.)
Char. B, E: 2.5% max.
Char. F: 5.0% max.
The dissipation factor should be measured at 20°C with
1±0.2kHz and AC5V(r.m.s.) max.
Char. B: Within ±10%
Char. E: Within +20/-55%
Char. F: Within +30/-80%
The capacitance measurement should be made at each step
specified in Table.
8 Temperature Characteristics
Pre-treatment: Capacitor should be stored at 85±2°C for 1 hr., then placed at
room condition* for 24±2 hrs. before measurements.
Step
1
2
3
4
5
Temp. (°C) 20±2 -25±3 20±2 85±2 20±2
Pull
9 Strength of Lead
Bending
Lead wire should not be cut off.
Capacitor should not be broken.
As shown in the figure at right, fix the body of
the capacitor and apply a tensile weight
gradually to each lead wire in the radial
direction of the capacitor up to 10N (5N for
9
lead diameter 0.5mm), and keep it for 10±1
W
sec.
Each lead wire should be subjected to 5N (2.5N for lead
diameter 0.5mm) of weight and bent 90° at the point of egress,
in one direction, then returned to its original position and bent
90° in the opposite direction at the rate of one bend in 2 to 3
sec.
10
Vibration
Resistance
Appearance
Capacitance
D.F.
No marked defect
Within specified tolerance
Char. B, E: 2.5% max.
Char. F: 5.0% max.
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
total amplitude, with about a 1 minute rate of vibration change
from 10Hz to 55Hz and back to 10Hz. Apply for a total of 6 hrs.,
2 hrs. each in 3 mutually perpendicular directions.
11 Solderability of Leads
Lead wire should be soldered with
uniform coating on the axial direction
over 3/4 of the circumferential direction.
The lead wire of a capacitor should be dipped into a ethanol
solution of 25wt% rosin and then into molten solder for 2±0.5
sec. In both cases the depth of dipping is up to about 1.5 to
2mm from the root of lead wires.
Temp. of solder: Lead Free Solder (Sn-3Ag-0.5Cu) 245±5°C
H63 Eutectic Solder 235±5°C
Appearance
12 ^{Soldering Effect}
(Non-Preheat)
Capacitance
Change
Dielectric Strength
(Between Lead
Wires)
No marked defect
Char. B: Within ±5%
Char. E: Within ±15%
Char. F: Within ±20%
Per item 4.
The lead wire should be immersed into the melted solder of
350±10°C (Body of ø5mm and under: 270±5°C) up to about 1.5
to 2mm from the main body for 3.5±0.5 sec.
(Body of ø5mm and under: 5±0.5 sec.)
Pre-treatment: Capacitor should be stored at 85±2°C for 1 hr.,
then placed at room condition* for 24±2 hrs.
before initial measurements.
Post-treatment: Capacitor should be stored for 4 to 24 hrs. at
room condition*.
* "room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued on the following page.
47