TPS_CPCI-A-3U-200C Datasheet, PDF (1/4 Pages) Murata Manufacturing Co., Ltd. – 200W 3Ux8HP AC/DC CompactPCI

cPCI-A-3U-200C Series
200W 3Ux8HP AC/DC CompactPCI™
SELECTION GUIDE
Model Number
Power
CPCI-A-3U-200C
200W
Output Current¹
Ḥ
5V 3.3V 12V -12V
For full details go to
www.murata-ps.com/rohs
25A 36A 5A 0.5A
Yes
Yes
INPUT CHARACTERISTICS
Parameter
Input Operating Voltage
Input Frequency
Input Current
Power Factor
Inrush Current
Conditions
Auto range, single phase
230Vac
230Vac and 115Vac, full load
230Vac
Min Typ Max Units
90
264 Vac
47
63 Hz
3.5
A_rms
0.98
50
A_pk
FEATURES
3Ux8HP package
200W power at -5 to 55ºC
OUTPUT CHARACTERISTICS
Output
Nominal Voltage
Output Current
Min
Max
PICMG 2.11 Compliant
V1¹
+5.0Vdc
0A
25A
Widerange 90-264VAC Input
Active power factor correction to EN61000-3-2
Class B conducted EMI performance
47-pin I/O Connector
80% efficiency
V2¹
V3¹
V4¹
Parameter
Line Regulation
PARD (V1 & V2)⁴
+3.3Vdc
+12Vdc
-12Vdc
Conditions
All outputs
20MHz bandwidth
0A
36A
0A
5A
0A
0.5A
Min
Typ
0.5
Full power with just 250lfm airflow
Hot-swap capable
PARD (V3 & V4)⁴
Hold-up Time
Turn-on Delay
20MHz bandwidth
220Vac, full load
14
DESCRIPTION
The cPCI-A-3U-200C is a high-reliability, 200W, continu-
ous power, 3Ux8HP CompactPCI™ power supply devel-
oped for chassis’ with airflows as low as 250lfm. The use
of 2 converters operating in parallel for the 3.3V and the
5V outputs enables maximum current draw on the two
outputs simultaneously. Compliant with the PICMG 2.11
standard.
With a widerange input of 90-264VAC, safety agency
approvals to UL60950 and EN60950, EMI compliance
to Class B FCC and EN55022 standards, the cPCI-A-
3U-300C was designed with globally-deployed systems
in mind. Additional features include remote sense com-
pensation, unit enable control (EN#), output inhibit control
(INH#), output fault signal (FAL#), and thermal warning
signal (DEG#). LEDs are provided for visual indication of
input power presence and output fault condition.
Rise Time
Transient Response
Over-Voltage and Short Circuit
Protection⁵
Remote Sense Compensation²
Current Share Tolerance³
Isolation
10% to 90% of full value
30
ΔV, 50% load step
Settling time
V1, V2, & V3: Latching
110
V1, V2
V1, V2
Pri-Sec
Pri-Chassis
Sec-Chassis
200
3
1.5
100
Notes:
1. Maximum combined power any combination of outputs is 200W
2. Maximum voltage compensation for cable losses .
3. Tolerance applicable up to 6 parallel units. Single wire current share on V1 & V2 for 50% to 100% load.
4. Measured across 1μF ceramic capacitor and 120μF electrolytic capacitor.
5. Automatic recovery upon removal of overload condition.
Load Regulation¹
±1%
±1%
±4%
±4%
Max
Units
%
75
mV_p-p
120
mV_p-p
msec
2
sec
msec
±5
%V_nom
500
μsec
130
%V_nom
mV
±10
%
kVac
kVac
Vdc
www.murata-ps.com
cPCI-A-3U-200C.A01 Page 1 of 4