SF1088A Datasheet, PDF (1/8 Pages) RF Monolithics, Inc – 170.6 MHz SAW Filter

• Designed for GSM BTS Receiver IF Applications
• Low Insertion Loss
• Excellent Size-to-Performance Ratio
• Hermetic SMP-75 Surface-Mount Case
• Unbalanced Input and Output
• Complies with Directive 2002/95/EC (RoHS) Pb
Absolute Maximum Ratings
Rating
Maximum Incident Power in Passband
Max. DC voltage between any 2 terminals
Storage Temperature Range
Suitable for lead-free soldering - Max. Soldering Profile
Value
Units
+10
dBm
30
VDC
-40 to +85
°C
260°C for 30 s
Electrical Characteristics
Characteristic
Sym
Notes
Min
Nominal Center Frequency
f_C
1
Passband
Insertion Loss at fc
IL
1 dB Passband
1, 2
±90
Amplitude Ripple over fc±90 kHz
Group Delay Variation over fc ±190 kHz GDV
Rejection
fc-0.6 to fc-0.4 and fc+0.4 to fc+0.6 MHz
1, 2, 3
13
fc-0.8 to fc-0.6 and fc+0.6 to fc+0.8 MHz
27
fc-1.6 to fc-0.8 and fc+0.8 to fc+1.6 MHz
40
fc-3.0 to fc-1.6 and fc+1.6 to fc+3.0 MHz
43
fc-5.8 to fc-3.0 and fc+3.0 to fc+5.8 MHz
47
fc-35 to fc-5.8 and fc+5.8 to fc+35 MHz
50
fc-75 to fc-35 and fc+35 to 75 MHz
45
DC to fc-75 and fc+75 to fc+1000 MHz
40
Operating Temperature Range
T_A
1
-10
SF1088A
170.6 MHz
SAW Filter
SMP-75
Typ
170.600
<500
15
35
45
55
55
55
55
Max
8.0
1.0
1000
+85
Units
MHz
dB
kHz
dB_P-P
ns_P-P
dB
°C
Impedance Matching to 50 Ω unbalanced
Case Style
Lid Symbolization (YY = year, WW = week)
External L-C
SMP-75 19 x 6.5 mm Nominal Footprint
RFM SF1088A YYWW
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature range
with filter soldered to the specified demonstration board with impedance matching to 50 W
and measured with 50 Ω network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center
frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband.
Rejection in final user application is dependent on PCB layout and external impedance
matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E"
indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However,
impedances and impedance matching may vary between Port 1 and Port 2, so that the fil-
ter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. Electrostatic Sensitive Device. Observe precautions for handling.
Electrical Connections
Connection
Port 1 Hot
Port 1 Gnd Return
Port 2 Hot
Port 2 Gnd Return
Case Ground
Terminals
10
1
5
6
All others
RF Monolithics, Inc. Phone: [phone]
Fax: [phone]
RFM Europe
Phone: [phone]
Fax: [phone]
©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail: [e-mail]
http://www.rfm.com
SF1088A-121504
Page 1 of 3