|
RBE-12 Datasheet, PDF (1/15 Pages) Murata Manufacturing Co., Ltd. – Eighth-Brick 240-Watt Isolated DC/DC Converters | |||
|
www.murata-ps.com
RBE-12/20-D48 Series
Eighth-Brick 240-Watt Isolated DC/DC Converters
Typical unit
FEATURES
ï®ï 240 Watts total output power, ï¬xed12 VDC @ 20 A
ï®ï 94.5% ultra-high efficiency at full load with
regulation
ï®ï 36 to 75 Volt DC input range (48 VDC nominal)
ï®ï Standard eighth-brick footprint
ï®ï 0.4-inch (10.2 mm) low height (no baseplate)
ï®ï Synchronous rectiï¬er topology with 100 mV
(typ.) ripple & noise
ï®ï Up to +85° Celsius thermal performance (with
derating)
ï®ï Stable no-load operation
ï®ï Fully isolated to 2250 VDC (BASIC, no baseplate)
ï®ï Remote On/Off enable control
ï®ï Extensive protection features â SC, OC, UVLO, OT
ï®ï Certiï¬ed to safety, emissions and environmental
standards
ï®ï Meets UL 60950-1, CAN/CSAC22.2 No. 60950-1,
IEC60950-1, EN60950-1 safety approvals
(2nd Edition) (pending)
PRODUCT OVERVIEW
The fully isolated (2250 Vdc, no baseplate) RBE-
12/20-D48 series accept a 36 to 75 Volt DC input
voltage range (48 VDC nominal) and converts it to a
ï¬xed 12Vdc output. Applications include 48V-pow-
ered datacom and telecom installations, base
stations, cellular dataphone repeaters, instruments
and embedded systems. Wideband output ripple
and noise is a low 100 mV (typical), peak-to-peak.
Reduced open frame overall height of 0.4Ë (10.2
mm) ï¬ts tight card cages.
The RBEâs regulated synchronous-rectiï¬er
topology and ï¬xed frequency operation means
excellent efï¬ciencies up to 94.5%, enabling âno
heatsinkâ operation for most applications up to
+85° Celsius (see derating curves). âNo fanâ or
zero airï¬ow higher temperature applications may
use the optional base plate for cold plate mounting
or natural-convection heatsinks.
Electronic protection features include input
undervoltage lockout (UVLO) , output current limit,
short circuit hiccup, and overtemperature shut-
down. Available options include positive or negative
logic On/Off control, conformal coating, various
pin lengths, and the baseplate. Assembled using
ISO-certiï¬ed automated surface-mount techniques,
the RBE series is certiï¬ed to UL and IEC safety
standards.
F1
+Vin (1)
External
DC
Power
Source
On/Off
Control
(2)
Open = On
$MPTFE0GG
1PTJUJWF
MPHJD
-Vin (3)
Ḥ
*TPMBUJPO
Barrier
Controller
and Power
5SBOTGFS
Duty Cycle
3FHVMBUJPO
t4XJUDIJOH
t'JMUFST
t$VSSFOU4FOTF
Reference and
Error Ampliï¬er
Figure 1. Connection Diagram
Typical topology is shown. Murata Power Solutions
recommends an external fuse at F1.
For full details go to
www.murata-ps.com/rohs
(pending)
www.murata-ps.com/support
+Vout (8)
-Vout (4)
MDC_RBE-12-20-D48.A02Î Page 1 of 15
|
▷ |