|
NPH10S2405IC Datasheet, PDF (1/8 Pages) Murata Manufacturing Co., Ltd. – Isolated 10W Single Output DC/DC Converters | |||
|
www.murata-ps.com
FEATURES
ÂRoHS compliant
ÂHigh efï¬ciency to 87%
ÂPower density up to 1.5Wcm3
ÂUL1950 recognized
ÂIndustry standard pinout
ÂSurge rating to 12W
ÂNon latching current limit
Â1.5kV input to output isolation
ÂVersatile control options
ÂContinuous rating to 10W at 72ºC without
heatsink
ÂOperation to zero load
ÂProtected against load faults
ÂInternal over temperature protection
ÂUses no electrolytic capacitors
ÂFixed frequency
ÂNo external components required
DESCRIPTION
The NPH10S series of DC/DC converters combines
ease of application with versatility. The pin pattern
is based on the popular industry standard, but two
additional pins may optionally be ï¬tted to provide
a variety of features not commonly found on units
of this type. High efï¬ciency enables full rating to
be achieved in a small package without heat-
sinking. Thermally protected against sustained
overload. The copper case achieves efï¬cient heat
transfer and screening. The product range has
been recognised by Underwriters Laboratory (UL)
to UL 1950 for operational insulation, ï¬le number
E179522 applies.
Ḥ
For full details go to
www.murata-ps.com/rohs
www.murata-ps.com/support
NPH10S Series
Isolated 10W Single Output DC/DC Converters
SELECTION GUIDE
Order Code1
Current
Limit 2 (Typ.)
V
V
A
A
%
μF kHrs
NPH10S2403EiC 24
3.4 2.94
4.3
79
470
279
NPH10S2403iC
24
3.4 2.94
4.3
79
470
279
NPH10S2405EiC 24
5.1 1.96
3.1
83
470
275
NPH10S2405iC
24
5.1 1.96
3.1
83
470
275
NPH10S2412EiC 24
12.1 0.83
1.2
86
100
259
NPH10S2412iC
24
12.1 0.83
1.2
86
100
259
NPH10S2415EiC 24
15.1 0.67
1.1
86
47
243
NPH10S2415iC
24
15.1 0.67
1.1
86
47
243
NPH10S4803EiC 48
3.4 2.94
4.1
80
470
317
NPH10S4803iC
48
3.4 2.94
4.1
80
470
317
NPH10S4805EiC 48
5.1 1.96
2.8
83
470
312
NPH10S4805iC
48
5.1 1.96
2.8
83
470
312
Obsolete
Recommended
Alternative
NPH10S4812EiC 48
12.1 0.83
1.3
86
56
291 UEI15-120-Q48P-C
NPH10S4812iC
48
12.1 0.83
1.3
86
56
291 UEI15-120-Q48P-C
NPH10S4815EiC 48
15.1 0.67
1.0
87
22
272 UEI15-150-Q48P-C
NPH10S4815iC
48
15.1 0.67
1.0
87
22
272 UEI15-150-Q48P-C
INPUT CHARACTERISTICS
Parameter
Conditions
Voltage range
Continuous operation, 24V input types
Continuous operation, 48V input types4
Min. Typ. Max. Units
18
24
36
V
36
48
75
OUTPUT CHARACTERISTICS
Parameter
Conditions
Min. Typ. Max. Units
Voltage set point error
50% load after 30 mins at nominal sup-
ply voltage
0.5
%
Overall voltage error
Case temperature -40ºC to 110ºC
Load 0% - 100%
Input speciï¬ed range
1
2.5
%
Temperature coefï¬cient of
output voltage (slope)
Over any 10ºC span within the speciï¬ed
temperature range
50
250 ppmºC
Deviation of output voltage Speciï¬ed over temperature MIN-MAX
0.5
1
%
Line regulation
Load Regulation
Ripple
Operating voltage range, 50% load
0% - 100% rated load5
rms
0.05 0.1
%
0.5
%
70
mV
ABSOLUTE MAXIMUM RATINGS
Input voltage, 24V input types
Input voltage, 48V input types
Output voltage
Output trim control
Synchronisation/shutdown control
-0.5V to 40V 6
-0.5V to 80V 6
-0.3V to controlled output voltage (operating or non-operating)
-1V to +30V
±15V relative to input return
1. Parts ending with EiC have optional TRIM and SS pins ï¬tted.
2. Current is quoted when output is 95% of regulated voltage.
3. Calculated using MIL-HDBK-217F with nominal input voltage at full load.
4. For applications requiring UL 1950 recognition, input voltage must not exceed 60VDC.
5. A minimum load of 10% of rating is recommended for typical applications.
6. Absolute maximum value for 30 seconds. Prolonged application may damage the product.
All speciï¬cations typical at TA=25°C, nominal input voltage and rated output current unless otherwise speciï¬ed.
KDC_NPH10SC.J02 Page 1 of 8
|
▷ |