LQH88P Datasheet, PDF (1/2 Pages) Murata Manufacturing Co., Ltd. – Chip Inductor (Chip Coil) Power Inductor (Wire Wound Type)

Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type)
Data Sheet
1
Chip Inductor (Chip Coil) Power Inductor (Wire Wound Type)
LQH88P Series (3131 Size)
I Dimensions
8.0±0.2
I Packaging
Code
Packaging
L
180mm Embossed Tape
K
330mm Embossed Tape
Minimum Quantity
250
1000
8.0±0.2
1.9±0.2
1.9±0.2
(in mm)
I Rated Value (p: packaging code)
Part Number
Inductance
Inductance
Test Frequency
Allowable DC Current
(Based on Temperature Rise)
Allowable DC Current
(Based on Inductance Change)
DC Resistance
Self Resonance
Frequency (min.)
Class of Magnetic Shield
LQH88PN1R0N38p 1.0µH±30% 100kHz
8.00A
LQH88PN1R5N38p 1.5µH±30% 100kHz
7.10A
LQH88PN2R2N38p 2.2µH±30% 100kHz
6.40A
LQH88PN3R3N38p 3.3µH±30% 100kHz
5.00A
LQH88PN4R7N38p 4.7µH±30% 100kHz
4.20A
LQH88PN6R8N38p 6.8µH±30% 100kHz
3.80A
LQH88PN100M38p 10µH±20% 100kHz
3.15A
LQH88PN150M38p 15µH±20% 100kHz
2.45A
LQH88PN220M38p 22µH±20% 100kHz
2.25A
LQH88PN330M38p 33µH±20% 100kHz
1.75A
LQH88PN470M38p 47µH±20% 100kHz
1.45A
LQH88PN680M38p 68µH±20% 100kHz
1.10A
LQH88PN101M38p 100µH±20% 100kHz
1.00A
11.20A
0.006ohm±30% 100MHz Magnetic shield of magnetic powder in resin
8.50A
0.008ohm±30% 60MHz
Magnetic shield of magnetic powder in resin
8.00A
0.009ohm±30% 50MHz
Magnetic shield of magnetic powder in resin
7.00A
0.013ohm±30% 35MHz
Magnetic shield of magnetic powder in resin
6.00A
0.017ohm±30% 30MHz
Magnetic shield of magnetic powder in resin
4.50A
0.022ohm±30% 20MHz
Magnetic shield of magnetic powder in resin
3.60A
0.029ohm±30% 18MHz
Magnetic shield of magnetic powder in resin
3.00A
0.041ohm±30% 13MHz
Magnetic shield of magnetic powder in resin
2.70A
0.066ohm±30% 10MHz
Magnetic shield of magnetic powder in resin
1.90A
0.095ohm±30% 9MHz
Magnetic shield of magnetic powder in resin
1.50A
0.157ohm±30% 7MHz
Magnetic shield of magnetic powder in resin
1.25A
0.190ohm±30% 7MHz
Magnetic shield of magnetic powder in resin
1.00A
0.265ohm±30% 4MHz
Magnetic shield of magnetic powder in resin
Operating Temperature Range: -40 to +85°C
Only for reflow soldering.
I Notice (Allowable DC Current)
<Allowable DC Current>
When Allowable DC Current is applied to the
Products, self-generation of heat will rise to
40°C or less.
When Allowable DC Current is applied to the
Products, Inductance will be within +-30% of
nominal Inductance value.
Continued on the following page.
o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.4.30
http://www.murata.com/