|
D1U86P Datasheet, PDF (1/6 Pages) Murata Power Solutions Inc. – 86mm 1U Front End AC-DC Power Supply | |||
|
www.murata-ps.com
D1U86P-W-1600-12-HBxDC Series
86mm 1U Front End AC-DC Power Supply
FEATURES
ï®ï 1600W output power
ï®ï 94% minimum efï¬ciency at 50% load
ï®ï 12V main output
ï®ï 12V standby output of 30W
ï®ï 1U height: 3.4" x 7.75" x 1.59"
ï®ï 38.6 Watts per cubic inch density
ï®ï N+1 redundancy, including hot plugging (up to
8 in parallel)
ï®ï Current sharing on 12V main output
ï®ï Overvoltage, overcurrent,
overtemperature protection
ï®ï Internal cooling fan (variable speed)
ï®ï PMBus⢠/ I²C interface monitoring and control
ï®ï RoHS compliant
www.murata-ps.com/en/3d/acdc.html
www.murata-ps.com/en/3d/acdc.html
www.murata-ps.com/en/3d/acdc.html
www.murata-ps.com/en/3d/acdc.html
www.murata-ps.com/en/3d/acdc.html
www.murata-ps.com/en/3d/acdc.html
Available now at
http://power.murata.com/en/3d/acdc.html
Ḥ
For full details go to
www.murata-ps.com/rohs
PRODUCT OVERVIEW
The D1U86P-W-1600-12-HBxDC products are high efï¬ciency 1600 watt, power factor corrected front end
supplies with a 12V main output and a 12V (30W) standby. They have current sharing and up to 8 supplies
may be operated in parallel. The supplies may be hot plugged, they recover from overtemperature faults,
and have logic and PMBus monitoring and control. Their low proï¬le 1U package and >38.6W/cubic inch
power density make them ideal for delivering reliable, efï¬cient power to servers, workstations, storage
systems and other 12V distributed power systems.
ORDERING GUIDE
Part Number
D1U86P-W-1600-12-HB4DC
D1U86P-W-1600-12-HB3DC
Power Output; AC Line
(90-264V) (108-264V) (180-264V)
1200W 1350W 1600W
Main
Output
12V
Standby
Output
12V
Airflow
Back to front
Front to Back
INPUT CHARACTERISTICS
Parameter
Input Voltage Operating Range
Frequency
Turn-on Voltage
Turn-off Voltage
Maximum Input Current
Inrush Current
Power Factor
Efficiency (230Vac) excluding
fan load
Conditions
Ramp up
Ramp down
1200W, 100Vac
At 264Vac at 25°C cold start
At 230Vac, half load
20% load
50% load
100% load
Min. Nom. Max.
90 115/230 264
47 50/60 63
81
89
70.5
73
78
14.1
35
0.98
90
94
91
Units
Vac
Hz
Vac
Arms
Apk
%
OUTPUT VOLTAGE CHARACTERISTICS
Output
Voltage
12V
12VSB
Parameter
Voltage Set Point
Line and Load Regulation
Droop
Ripple Voltage & Noise1
Output Current (230 Vac)2
Output Current (120 Vac)2
Output Current (100 Vac)2
Load Capacitance
Voltage Set Point
Ripple Voltage & Noise1
Output Current
Conditions
50% load
20MHz Bandwidth
50% load
20MHz Bandwidth
Min.
12.17
11.4
0
0
0
11.97
0
Typ. Max.
12.2 12.23
12.6
3.10
120
133.4
112.5
100.0
10,000
12.0 12.02
120
2.5
Units
Vdc
mV/A
mV p-p
A
A
A
μF
Vdc
mV p-p
A
1 Ripple and noise measured with a parallel combination of a 1.0μF ceramic and 10μF tantalum capacitor on each of the power module
outputs. A short coaxial cable connected directly to the input of a scope is required.
2 To meet ripple and transient step load speciï¬cations a minimum load of 4A is required.
CB
Test Certiï¬cate
and Test Report
www.murata-ps.com/support
D1U86P-W-1600-12-HBxDC.A01 Page 1 of 6
|
▷ |