MSK182 Datasheet, PDF (3/8 Pages) M.S. Kennedy Corporation – DUAL HIGH VOLTAGE/ HIGH CURRENT OPERATIONAL AMPLIFIER

ABSOLUTE MAXIMUM RATINGS
VCC Total Supply Voltage ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ _60V
±IOUT Output Current (within S.O.A.)
5A ○
○
○
○
○
○
VIND Input Voltage (Differential)
±29.5V
○
○
○
○
○
○
VIN Input Voltage (Common Mode) _+27V/-29V
TJ Junction Temperature ○ ○ _{Internal Protection}
(See Application Note)
ELECTRICAL SPECIFICATIONS
TST Storage Temperature Range ○ ○ ○ ○ ○ ○ -65°C to +150°C
TLD
Lead Temperature Range
300°C
○
○
○
○
○
○
○
○
○
○
○
○
○
○
(10 seconds)
TC Case Operating Temperature
(MSK182G/E/184G/E/185G/E) See Note 9 -40°C to +125°C
(MSK182/183/184/185) ○ ○ ○ ○ ○ ○ ○ ○ -25°C to +85°C
RTH Thermal Resistance (Per Amplifier)
MSK182 - Junction to Case @ 125°C ○ ○ ○ ○ ○ 1.8°C/W
MSK183 - Junction to Case @ 125°C ○ ○ ○ ○ ○ 3.0°C/W
MSK184 - Junction to Case @ 125°C ○ ○ ○ ○ ○ 3.5°C/W
MSK185 - Junction to Case @ 125°C ○ ○ ○ ○ ○ 4.0°C/W
Parameter
Test Conditions 1 2
Group A
MSK182G/E
184G/E/185G/E
MSK182/MSK183/
MSK184/MSK185
Subgroup Min. Typ. Max. Min. Typ. Max.
Units
STATIC
Supply Voltage Range 3
-
±4
- ±30 ±4
-
±30 V
Quiescent Current (Per Amp)
VIN=0V
1
-
±17 ±20 -
±17 ±23 mA
2,3
-
±17 ±20 -
-
-
mA
Quiescent Current (Per Amp) 7
Shutdown Mode VIN=0V
-
-
±6
-
-
±6
-
mA
INPUT
Input Offset Voltage
VIN=0V
1
-
±2 ±10 -
±2 ±15 mV
Input Offset Voltage Drift
VIN=0V
-
- ±30 -
- ±30
- µV/°C
Input Bias Current 3
VIN=0V
1
- ±100 ±500 - ±100 ±750 nA
Input Offset Current ₃
Input Impedance
VIN=OV
f=DC
1
±1 ±5 ±50 -
±5 ±75 nA
-
-
10 ⁷
-
-
10 ⁷
-
Ω
Input Capacitance
f=DC
Common Mode Rejection Ratio 3 (-VCC)-0.1≤ VIN ≤ (+VCC)-3V
Input Voltage Noise Density
f=1KHZ
-
-
6
-
-
6
-
pF
1
80
95
-
75 95
-
dB
-
-
90
-
-
90
- nV/√HZ
OUTPUT
Output Voltage Swing
IOUT=0.6A 3
IOUT=3.0A
4
±27 ±28
- ±27 ±28
-
V
4 ±25.5 ±26 - ±25 ±26
-
V
Output Current
DC=Continuous
4
±3
-
- ±3
-
-
A
VE/S High- Output Enabled E/S Open or High
4
-27.5 -
- -27.5 -
-
V
Shutdown Input 3 7
VE/S Low- Output Disabled E/S Forced Low
IE/S High- Output Enabled E/S Open or High
4
-
-
-29 -
-
-29
V
-
-
-65
-
-
-65
-
µA
IE/S Low- Output Disabled E/S Forced Low
-
-
-70
-
-
-70
-
µA
Output Disable Time 7
-
-
1
-
-
1
-
µS
Output Enable Time 7
-
-
3
-
-
3
-
µS
TRANSFER CHARACTERISTICS
Slew Rate
Open Loop Voltage Gain 3
AV=1 VOUT= 50Vp-p RL=8Ω
VOUT=±25V RL=1KΩ
-
-
10
-
-
8
-
V/µS
4
90
98
-
88 98
-
dB
Settling Time ±0.1% 3
AV=10 50V Step
-
-
15
-
-
18
-
µS
NOTES:
1 Unless otherwise specified ±VCC= ±30VDC and E/S pin is open for MSK 182 and MSK 183.
2 All electrical specifications apply to each amplifier.
3 Devices shall be capable of meeting the parameter, but need not to be tested. Typical parameters are for reference only.
4 Industrial grade and 'E' suffix devices shall be tested to subgroups 1 and 4 unless otherwise specified.
5 Military grade devices ('G' suffix) shall be 100% tested to subgroups 1,2,3 and 4.
6 Subgroup 1,4 TA=TC=+25°C
Subgroup 2 TA=TC=+125°C
Subgroup 3 TA=TC=-40°C
7 Does not apply to MSK 184 or MSK185.
8 Refer to SMD 5962-92152 for electrical parameters for devices purchased as such.
9 The operating temperature range is -55°C to +125°C if the device is powered. The minimum cold start temperature is -40°C.
3
Rev. I 3/04