DAC2815D_15 Datasheet, PDF (3/9 Pages) M.S. Kennedy Corporation – All Ceramic Capacitors

ELECTRICAL SPECIFICATIONS
DAC2812D
Parameter
Test Conditions 1
Output Voltage
Output Current 2 8
11V≤VIN≤50V
16V≤VIN≤40V
Output Voltage Ripple
Input Current Ripple 2
Line Regulation
Load Regulation
Cross Regulation 10
BW=10KHz to 2MHz
BW=10KHz to 2MHz
LIN=2µH
VIN=11,28 and 40V
±IOUT=209mA
VIN=28VDC
±IOUT=0,105 and 209mA
Efficiency
Step Load Response
Step Load Recovery
Step Line Response 2
Step Line Recovery 2
Start Up Overshoot
±IOUT=105mA to/from 209mA
Transition TIme=30µS
±IOUT=105mA to/from 209mA
Transition TIme=30µS
VIN=16V to/from 40V
Transition Time=30µS
VIN=16V to/from 40V
Transition Time=30µS
Start Up Delay
Shutdown Delay 2
Shutdown Recovery 2
Input Voltage Range 2
Quiescent Current
Capacitive Load 2 9
Isolation
Short Circuit Current Limit 7
Switching Frequency
VOUT Adjustment Range
POUT=6.0W MAX.
POUT=5W MAX.
Enabled, IOUT=0mA
Disabled IOUT=0mA
Per Output
VIN=16-40V
VIN=11-50V
Input to output or any pin to case @ 500V
RPOT=50KΩ
Group A DAC2812D H/E
Subgroup
Min. Typ. Max.
DAC2812D
Units
Min. Typ. Max.
1
±11.9 ±12.0 ±12.1 ±11.85 ±12.0 ±12.15 VDC
2,3 ±11.76
- ±12.24
-
-
-
VDC
1
±208
-
-
±208 -
-
mA
2,3
±208
-
-
-
-
-
mA
1
±250
-
-
±250 -
-
mA
2,3
±250
-
-
-
-
-
mA
1
-
15
60
-
15
60 mVrms
2,3
-
-
100
-
-
- mVrms
1
-
85 140
-
85
140 mAp-p
2,3
-
-
225
-
-
- mAp-p
1
-
±5 ±25
-
±5 ±30 mV
2,3
-
-
±50
-
-
-
mV
1
-
±5 ±25
-
±5 ±30 mV
2,3
-
-
±50
-
-
-
mV
1
-
0.1
1
-
0.1
1
%
2,3
-
0.1
1
-
-
-
%
1
60
64
-
60
64
-
%
2,3
60
-
-
-
-
-
%
4
-
±400
-
- ±400
-
mV
5,6
-
±400
-
-
-
-
mV
4
-
200
-
-
200
-
µS
5,6
-
200
-
-
-
-
µS
4
-
±200 ±500
- ±200 ±500 mV
5,6
-
- ±500
-
-
-
mV
4
-
250
-
-
250
-
µS
5,6
-
250
-
-
-
-
µS
4
-
0
200
-
0
200 mV
5,6
-
-
200
-
-
-
mV
4
-
40
60
-
40
60
mS
5,6
-
-
60
-
-
-
mS
4
-
250 500
-
250 500 µS
5,6
-
200
-
-
-
-
µS
-
-
40
60
-
40
60
mS
1,2,3
16
-
40
16
-
40
V
1,2,3
11
-
50
11
-
50
V
1,2,3
-
50
70
-
50
70
mA
1,2,3
-
1.25 2.5
-
1.25 2.5 mA
1,2,3
-
-
100
-
-
100
µF
1,2,3
-
-
50
-
-
50
µF
1
100
-
-
100
-
-
MΩ
1
-
-
-
-
-
-
A
4
375 400 425
350 400 450 KHz
1
±10
-
±10
-
-
%
NOTES:
1 +VIN = 28V, IOUT = ±250mA, TA=TC=25°C unless otherwise specified.
2 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
3 Industrial grade and "E" suffix devices shall be tested to subgroups 1 and 4 unless otherwise specified.
4 Military grade devices ("H" suffix) shall be 100% tested to subgroups 1, 2, 3 and 4.
5 Subgroups 5 and 6 testing available upon request.
6 Subgroup 1, 4 TA=TC=+25°C
2, 5 TA=TC=+125°C
3, 6 TA=TC= -55°C
7 Device has internal shutdown feature that pulses the output with a low duty cycle during faults.
8 Up to 80% of total load may be drawn from either output.
9 Connect capacitors from + output to common and -output to common only. Do not exceed a 4:1 capacitor imbalance.
10 1.0W load on output under test, 1.0W to 4.0W load change on the other.
3
Rev. E 9/07