MSK707H Datasheet, PDF (2/6 Pages) M.S. Kennedy Corporation – ULTRA-ACCURATE/HIGH SLEW RATE INVERTING OPERATIONAL AMPLIFIER

ABSOLUTE MAXIMUM RATINGS
±VCC
IOUT
VIN
RTH
Supply Voltage ±18V ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Peak Output Current
○
○
○
○
○
○
○
○
○
○ ±200mA
Differential Input Voltage ○ ○ ○ ○ ○ ○ ○ ○ ○ ±12V
Thermal Resistance ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 46°C/W
Junction to Case
Output Devices Only
TST Storage Temperature Range ○ ○ -65°C to +150°C
TLD Lead Temperature Range ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 300°C
(10 Seconds Soldering)
PD Power Dissipation ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ See Curve
TJ Junction Temperature ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 150°C
TC Case Operating Temperature Range
(MSK707H/E)
-55°C to+125°C
○
○
○
○
○
○
○
○
○
○
(MSK707) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ -40°C to +85°C
ELECTRICAL SPECIFICATIONS
±Vcc=±15V Unless Otherwise Specified
Parameter
Test Conditions
Group A
MSK 707H/E
MSK 707
Subgroup Min. Typ. Max. Min. Typ. Max. Units
STATIC
Supply Voltage Range 2
-
±12 ±15 ±18 ±12 ±15 ±18 V
Quiescent Current
Vin=0V
1
-
±35 ±37 -
±37 ±40 mA
Av=-1V/V
2,3
-
±36 ±39 -
-
-
mA
Thermal Resistance ²
Output Devices Junction to Case
-
-
45
-
-
48
- °C/W
INPUT
Input Offset Voltage
Vin=0V Av=-100V/V
1
-
±25 ±75 -
±50 ±100 µV
Input Offset Voltage Drift ²
Vin=0V
2,3
- ±0.5 ±1.5 - ±0.75 ±2.0 µV/°C
Input Bias Current ^{7 2}
Vcm=0V
1
-
±10 ±40 -
±20 ±60 nA
Either Input
2,3
-
±15 ±80 -
-
-
nA
Input Offset Current 2
Vcm=0V
1
-
5
20
-
10
30
nA
2,3
-
5
40
-
-
-
nA
Input Impedance 2
F=DC Differential
-
-
5
-
-
5
-
MΩ
Power Supply Rejection Ratio 2
∆Vcc=±5V
-
-
1
8
-
2
20 µV/V
Input Noise Voltage ²
F= 0.1Hz To 10Hz
-
-
0.15
-
-
0.2
- µVp-p
Input Noise Voltage Density 2
F=1KHz
-
-
3.8
-
-
4
- nV√Hz
Input Noise Current Density 2
F=1KHz
-
-
0.6
-
-
0.7
- pA√Hz
OUTPUT
Output Voltage Swing
RL=100Ω Av=-3V/V F≤10MHz
4
±10 ±12.5 - ±10 ±12.5 -
V
Output Current
TJ<150°C
4 ±100 ±120 - ±100 ±120 -
mA
Settling Time 1 2
0.1% 10V step RL=1KΩ
-
-
10
-
-
15
-
nS
Full Power Bandwidth
RL=100Ω Vo=±10V
4
20 22
-
15 20
-
MHz
Bandwidth (Small Signal) 2
RL=100Ω
-
175 220
- 165 190
-
MHz
TRANSFER CHARACTERISTICS
Slew Rate
VOUT=±10V RL=1KΩ Av= -1.5V/V
-
3000 4500
- 2500 4500 -
V/µS
Open Loop Voltage Gain 2
RL=1KΩ F=1KHz VOUT=±10V
4
100 110
-
95
105
-
dB
NOTES:
1 AV= -1, measured in false summing junction circuit.
2 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
3 Industrial grade and "E" suffix devices shall be tested to subgroups 1 and 4 unless otherwise specified.
4 Military grade devices ("H" suffix) shall be 100% tested to subgroups 1,2,3 and 4.
5 ^{Subgroups 5 and 6 testing available upon request.}
6 ^{Subgroup 1,4 TA=TC=+25°C}
Subgroup 2
TA=TC=+125°C
Subgroup 3
TA=TC=-55°C
7 Measurement taken 0.5 seconds after application of power using automatic test equipment.
2
PRELIMINARY Rev. - 2/04