MSK5010-33_15 Datasheet, PDF (2/7 Pages) M.S. Kennedy Corporation – Available in 3.3V, 5.0V and 12.0V versions

ABSOLUTE MAXIMUM RATINGS ⁹
VIN Input Voltage
VEN Enable Voltage
IOUT Output Current
TJ Junction Temperature
36V TST Storage Temperature Range ¹⁰
-0.3V to 36V TLD Lead Temperature Range
10A within SOA
(10 Seconds)
+175°C TC Case Operating Temperature
MSK5010 Series
MSK5010B Series
-65°C to +150°C
300°C
-40°C to +85°C
-55°C to +125°C
ELECTRICAL SPECIFICATIONS
Parameter
Output Voltage Tolerance
Dropout Voltage 2
Load Regulation
Line Regulation
Quiescent Current
Ripple Rejection 2
Thermal Resistance 2
Enable Input Voltage 2
Enable Input Current 2
Output Settling Time 2 8
Input Voltage Range 2
Test Conditions 3
IOUT=100mA; VIN=VOUT+3V
IOUT= 0A
IOUT=10A
VIN=VOUT+3V
100mA ≤ IOUT ≤ 9A
(VOUT +1.5V) ≤ VIN ≤ (VOUT+15V)
IOUT=100mA
VEN=VIN; VIN=VOUT+3V; IOUT=0A
2 VEN=0V; VIN=VOUT+3V; IOUT=0A
f=120Hz
Junction to Case
HIGH
LOW
HIGH
LOW
To within 10mV
Group A MSK5010B SERIES
MSK5010 SERIES
Subgroup Min. Typ. Max. Min.
Typ. Max. Units
1
-
±0.3 ±1.5 -
±0.5 ±1.5 %
2,3
-
±1.0 ±2.0 -
-
-%
1
-
0.002 0.010 -
0.002 0.015 V
1
-
0.45 0.75 -
0.5
1.0 V
1
-
±0.5 ±1.0 -
±0.5 ±1.5 %
2,3
-
±0.5 ±2.0 -
-
-%
1
-
±0.3 ±1.0 -
±0.5 ±1.5 %
2,3
-
±0.5 ±1.0 -
-
-%
1,2,3
-
4.5
10 -
4.5
10 mA
1,2,3
-
0.15 5.0 -
0.15
5.0 µA
-
-
45
-
-
45
- dB
-
-
0.7
0.8 -
0.7
1.0 °C/W
1
2.4
1.2
- 2.4
1.2
-
V
1
-
1.2
0.8 -
1.2
0.8 V
1
-
12.5
50
-
20
50 µA
1
-
0.8
25 -
10
25 µA
-
-
5
-
-
5
- µS
-
3
-
36 3
-
36 V
NOTES:
1 Output decoupled to ground using 47µF minimum capacitor unless otherwise specified.
2 Guaranteed by design but not tested. Typical parameters are representative of actual device
PART ₇
NUMBER
performance but are for reference only.
3 All output parameters are tested using a low duty cycle pulse to maintain TJ = TC.
4 Industrial grade devices shall be tested to subgroup 1 unless otherwise specified.
MSK5010-3.3
MSK5010-5.0
5 Military grade devices ('B' suffix) shall be 100% tested to subgroups 1,2 and 3.
6 Subgroup 1
TA=TC=+25°C
MSK5010-12
Subgroup 2
TA=TC=+125°C
Subgroup 3
TA=TC= -55°C
7 Please consult the factory if alternate output voltages are required.
8 After application of enable pulse.
9 Continuous operation at or above absolute maximum ratings may adversly effect the device performance and/or life cycle.
10 Internal solder reflow temperature is 180°C, do not exceed.
OUTPUT
VOLTAGE
+3.3V
+5.0V
+12.0V
2
8548-149 Rev. J 2/15