MSK4410_15 Datasheet, PDF (2/8 Pages) M.S. Kennedy Corporation – 55 Volt Motor Supply Voltage

ABSOLUTE MAXIMUM RATINGS ³
V+
High
Voltage
Supply
○
4
○
○
○
○
○
○
○
○
○
○
○ +55V
VIN
Speed Command (+,-) ^{○ ○ ○ ○ ○ ○ ○ ○ ○ ○±15VIN}
VIND
Hall A,B,C,Brake ^{○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ +V REF}
IOUT
Continuous Output Current ○
○
○
○
○
○
○
○
10A
○
IpK
Peak Output Current ○
○
○
○
○
○
○
○
○
○
○
○
15A
○
+15VIN +15 Volt Input Voltage ^{○ ○ ○ ○ ○ ○ ○ ○ ○ ○ +16V}
-15VIN -15 Volt Input Voltage ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ^-16V
OJC Thermal Resistance (@ 125°C) ○ ○ ○ ○ ○ ○ 8.8°C/W
TST Storage Temperature Range ○ ○ ○-55°C to +125°C
TLD Lead Temperature Range ○ ○ ○ ○ ○ ○ ○ ○ ○ ○+300°C
(10 Seconds)
TC Case Operating Temperature
MSK4410 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ -40°C to +85°C
TJ Junction Temperature ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○+150°C
ELECTRICAL SPECIFICATIONS
Parameter
PWM
Clock Frequency
POWER SUPPLY REQUIREMENTS
+15 Volt Input Current
-15 Volt Input Current
HALL INPUTS
VIL 2
VIH 2
ANALOG SECTION
Speed Command Input Range
Speed Command Input Range
Speed Command Input Current 2
REFERENCE OUTPUT VOLTAGE
Reference Voltage
ERROR AMP
Input Offset Voltage 2
Input Offset Current 2
Input Bias Current 2
Input Common Mode Voltage Range 2
Open-Loop Voltage Gain 2
Input Common Mode Rejection Ratio 2
Power Supply Rejection Ratio 2
OUTPUT SECTION
Voltage Drop Across Bridge (1 Upper & 1 Lower) 2
Voltage Drop Across Bridge (1 Upper & 1 Lower) 2
Leakage Current 2
Diode VSD 2
trr 2
Dead Time 2
TACH OUT
Output Voltage High State
Output Voltage Low State
Output Pulse Width
CURRENT LIMIT
Current Limit 1 Amp
Test Conditions 1
E/A DC Gain=1, Positive Command
E/A DC Gain=1, Negative Command
VIN=5V
@ 1mA
VO=3V, RL=15K
10 AMPS
10 AMPS @ 150°C Junction
All switches off, V+=44V, 150°C Junction
I Source = 5mA
I Sink = 10mA
R/C=20K/0.01uF
Current Limit Adjust Pin=Open
MSK 4410
Min. Typ. Max.
Units
20
-
-
-
3.0
1.2
-1.2
-
5.82
-
-
-
0
70
55
65
-
-
-
-
-
-
3.60
-
150
0.3
25
37
8
-
-
-
-
-
6.24
0.4
8.0
-46
-
80
86
105
0.8
1.6
-
-
86
2
3.95
0.25
200
1
30
60
18
0.8
-
4.5
-4.5
1.5
6.57
10
500
-1000
VREF
-
-
-
-
1.92
750
1.6
-
-
4.20
0.50
250
1.70
KHz
mA
mA
VOLTS
VOLTS
VOLTS
VOLTS
mA
VOLTS
mV
nA
nA
V
db
db
db
VOLTS
VOLTS
μA
VOLTS
nSec
μSec
V
V
μSec
Amps
NOTES:
1 ±15V INPUT=±15V, V+=28V, BRAKE=GND unless otherwise specified.
2 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
3 Continuous operation at or above absolute maximum ratings may adversely effect the device perfomance and/or life cycle.
4 When applying power to the device, apply the low voltage followed by the high voltage or alternatively, apply both at the same time.
Do not apply high voltage without low voltage present.
2
Rev. E 1/11