MSK4362_15 Datasheet, PDF (2/9 Pages) M.S. Kennedy Corporation – 75 Volt Motor Supply Voltage

ABSOLUTE MAXIMUM RATINGS ⁹
High Voltage Supply (internal regulators disabled) ¹⁰
75V
High Voltage Supply (using internal regulators)
55V
Current Command Input
±13.5V
Logic Inputs
-0.2V to REFOUT
±15VOUT External Load
±50 mA
REFOUT External Load
15 mA
E/A OUT External Load
5 mA
Clock SYNC Input
-0.2V to +15V
Continuous Output Current
30 Amps
Peak Output Current
41 Amps
RθJC
RθJC
TST
TLD
TC
TJ
Thermal Resistance (Output Switches)
Thermal Resistance (Regulator)
Storage Temperature Range ¹¹
Lead Temperature Range
(10 Seconds)
Case Operating Temperature
MSK4362
MSK4362H
Junction Temperature
1.5°C/W
9°C/W
-65°C to +150°C
+300°C
-40°C to +125°C
-55°C to +125°C
+150°C
ELECTRICAL SPECIFICATIONS
Parameter
Test Conditions
Group A
MSK4362H ³
Subgroup _{Min. Typ. Max.}
MSK4362 2
Min. Typ. Max.
Units
INPUT CURRENT
+15 VIN
Output PWM'ing
1
-
65
90
-
65
90
mA
-15 VIN
Current Command=0 Volts
1
-
25
40
-
25
40
mA
PWM
Clock Free Running Frequency
4
21
22
23
20
22
24
KHz
5,6
18.7
22
25.3
-
-
-
KHz
CLOCK SYNC INPUT
VIL 1
-
-
-
2.5
-
-
2.5 VOLTS
VIH 1
-
12.5
-
-
12.5
-
- VOLTS
Duty Cycle 1
-
10
-
90
10
-
90
%
SYNC Frequency 1
- Clock +0 - Clock +3 Clock +0 - Clock +3 KHz
REGULATORS
VIN=28V
+15 VOUT
25mA External Load 6
1,2,3 14.25
-
15.75 14.25
-
15.75 VOLTS
-15 VOUT
25mA External Load 6
1,2,3 -14.25
-
-15.75 -14.25
-
-15.75 VOLTS
REFOUT
15mA External Load
1,2,3 5.82
-
6.57 5.82
-
6.57 VOLTS
-15 VOUT Ripple
25mA External Load 6
4
-
-
250
-
-
250
mV
LOGIC INPUTS
(Hall A,B,C,Brake,60°/120°,DIS)
VIL 1
-
-
-
0.8
-
-
0.8 VOLTS
VIH 1
-
3.0
-
-
3.0
-
- VOLTS
ANALOG SECTION
Current Command Input Range 1
-
-13.5
-
+13.5 -13.5
-
+13.5 VOLTS
Current Command Input Current 1
-
-
-
1.5
-
-
1.5
mA
Transconductance 8
4
2.70
3
3.30 2.55
3
3.45 A/V
5,6
2.4
3
3.6
-
-
-
A/V
Offset Current
Current Command=0Volts
1
-50
0
2,3
-100
0
50
-100
0
100
-
-
100
mA
-
mA
Current Monitor 8
4
0.300 0.33 0.367 0.280 0.33 0.380 V/A
5,6 0.280 0.33 0.380 0.250 0.33 0.410 V/A
Current Monitor Voltage Swing 1
5mA Load
-
-12
-
+12
-12
-
+12 VOLTS
ERROR AMP
E/A OUT Swing 1
5mA Load
-
-12
-
+12
-12
-
+12 VOLTS
Slew Rate 1
-
6.5
8
-
6.5
8
- V/µSec
Gain Bandwidth Product 1
-
6.5
-
-
6.5
-
MHz
Large Signal Voltage Gain 1
-
175
275
-
175 275
-
V/mV
OUTPUT SECTION 1
Voltage Drop Across Bridge (1 Upper & 1 Lower) 1
30 AMPS
-
-
-
1
-
-
1 VOLTS
Voltage Drop Across Bridge (1 Upper & 1 Lower) 1
30 AMPS @ 150°c Junction
-
-
-
1.83
-
-
1.83 VOLTS
Leakage Current 1 7
All switches off, V+=60V, 150°C Junction
-
-
-
750
-
-
750
µA
Diode VSD 1
-
-
-
2.6
-
-
2.6 VOLTS
trr 1
-
-
280
-
-
280
-
nSec
Dead Time 1
-
-
2
-
-
2
-
µSec
NOTES:
1 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
2 Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise specified.
3 Military grade devices ("H" Suffix) shall be 100% tested to Subgroups 1, 2, 3 and 4.
4 Subgroups 5 and 6 testing available upon request.
5 Subgroup 1, 4 TA = TC = +25°C
2, 5 TA = TC = +125°C
3, 6 TA = TC = -55°C
6 Maximum power dissipation must be limited according to voltage regulator power dissipation. Tested with internal ±15V loading.
7 Hybrid powered by external ±15V supplies.
8 Measurements do not include offset current at 0V current command.
9 Continuous operation at or above absolute maximum ratings may adversly effect the device performance and/or life cycle.
10 When applying power to the device, apply the low voltage followed by the high voltage or alternatively, apply both at the same time.
Do not apply high voltage without low voltage present.
11 Internal solder reflow temperature is 180°C, do not exceed.
2
8548-147 Rev. M 1/15