MSK4310_15 Datasheet, PDF (2/9 Pages) M.S. Kennedy Corporation – 55 Volt Motor Supply Voltage

ABSOLUTE MAXIMUM RATINGS ⁷
V+
High
Voltage
Supply
○
8
○
○
○
○
○
○
○
○
○
○
○+55V
VIN
Speed Command (+,-) ^{○ ○ ○ ○ ○ ○ ○ ○ ○ ○± 1 5 V I N}
VIND
Hall A,B,C,Brake ^{○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ +V REF}
IOUT
Continuous Output Current ○
○
○
○
○
○
○
○
10A
○
IpK
Peak Output Current ○
○
○
○
○
○
○
○
○
○
○
○
15A
○
+ 1 5 V IN +15 Volt Input Voltage ^{○ ○ ○ ○ ○ ○ ○ ○ ○ ○ + 1 6 V}
-15VIN
-15 Volt Input Voltage ^○
○
○
○
○
○
○
○
○
○
-16V
○
ELECTRICAL SPECIFICATIONS
OJC Thermal Resistance (@ 125°C) ○ ○ ○ ○ ○ ○ 4.8°C/W
TST
Storage Temperature
Range
9
○
○
○
-65°C to +150°C
TLD Lead Temperature Range
(10 Seconds) +300°C ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
TC Case Operating Temperature
T MSK4310 -40°C to +85°C J
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
MSK4310H ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ -55°C to +125°C
Junction Temperature ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ +150°C
Parameter
Test Conditions
Group A
Subgroup
MSK4310H 3
Min. Typ. Max.
MSK4310 3
Min. Typ. Max.
Units
PWM
Clock Frequency
POWER SUPPLY REQUIREMENTS
4
21
25
29
5,6
20
25
30
20
25
30
KHz
-
-
-
KHz
+15 Volt Input Current
-15 Volt Input Current
HALL INPUTS
VIL 2
VIH 2
ANALOG SECTION
Speed Command Input Range
Speed Command Input Range
Speed Command Input Current 2
REFERENCE OUTPUT VOLTAGE
1
-
37
50
2,3
-
41
60
1
-
8
15
2,3
-
9
20
-
37
60
mA
-
-
-
mA
-
8
18
mA
-
-
-
mA
-
-
-
0.8
-
-
0 . 8 VOLTS
-
3.0
-
-
3.0
-
-
VOLTS
E/A DC Gain=1, Positive Command
1
1.2
-
4.5
1.2
-
4 . 5 VOLTS
E/A DC Gain=1, Negative Command
1
-1.2
-
-4.5
-1.2
-
-4.5 VOLTS
VIN=5V
-
-
-
1.5
-
-
1.5
mA
Reference Voltage
@ 1mA
ERROR AMP
Input Offset Voltage 2
Input Offset Current 2
Input Bias Current 2
Input Common Mode Voltage Range 2
Open-Loop Voltage Gain 2
VO=3V, RL=15K
Input Common Mode Rejection Ratio 2
Power Supply Rejection Ratio 2
OUTPUT SECTION
Voltage Drop Across Bridge (1 Upper & 1 Lower) 2
10 AMPS
Voltage Drop Across Bridge (1 Upper & 1 Lower) 2 10 AMPS @ 150°C Junction
Leakage Current 2
All switches off, V+=44V, 150°C Junction
Diode VSD 2
trr 2
Dead Time 2
TACH OUT
Output Voltage High State
I Source = 5mA
Output Voltage Low State
I Sink = 10mA
Output Pulse Width 1
CURRENT LIMIT
R/C=20K/0.01uF
Current Limit
Current Limit Adjust Pin=Open
NOTES:
1
2,3
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
4
1,2,3
5.9
5.82
-
-
-
0
70
55
65
-
-
-
-
-
-
3.60
-
150
0.4
6.24
-
6.5
6.57
0.4
10
8.0
500
-46 -1000
-
VREF
80
-
86
-
105
-
0.8
-
1.6
1.92
-
750
-
1.6
86
-
2
-
3.95
0.25
200
4.20
0.50
250
1
1.60
5.82
-
-
-
-
0
70
55
65
-
-
-
-
-
-
3.60
-
150
0.3
6.24
-
6.57
-
VOLTS
VOLTS
0.4
10
mV
8.0
500
nA
-46 -1000
nA
-
VREF
V
80
-
db
86
-
db
105
-
db
0.8
-
VOLTS
1.6
1.92 VOLTS
-
750
µA
-
1 . 6 VOLTS
86
-
nSec
2
-
µSec
3.95
0.25
200
4.20
0.50
250
V
V
µSec
1
1.70 Amps
1 ±15V INPUT=±15V, V+=28V, BRAKE=GND unless otherwise specified.
2 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
3 Industrial devices shall be tested to subgroups 1 and 4 unless otherwise specified.
4 Military grade devices ("H" Suffix) shall be 100% tested to Subgroups 1, 2, 3 and 4.
5 Subgroups 5 and 6 testing available upon request.
6 Subgroup 1, 4 TA = TC = +25°C
2, 5 TA = TC =+125°C
3, 6 TA = TC = -55°C
7 Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
8 When applying power to the device, apply the low voltage followed by the high voltage or alternatively,apply both at the same time.
Do not apply high voltage without low voltage present.
9 Internal solder reflow temperature is 180°C, do not exceed.
2
8548-72 Rev. F 12/14