MSK4201 Datasheet, PDF (2/6 Pages) M.S. Kennedy Corporation – 28 VOLT 5 AMP MOSFET H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER

ABSOLUTE MAXIMUM RATINGS ⁶
V+
VCC
IOUT
IPK
VOUT
θJC
High Voltage Supply 75V ⁷
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Logic Supply 16V ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Continuous Output Current ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5A
Peak Output Current ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 37A
Output Voltage Range GND-2V min. To V+ max.
Thermal Resistance @ 125°C Case ○ ○ ○ 2.3°C/W
(Output Switches)
TST
Storage
Temperature
Range
8
○
○ -65°C to +150°C
TLD Lead Temperature Range
(10 Seconds) 300°C ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
TC Case Operating Temperature
MSK4201 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ -40°C to +125°C
MSK4201B ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ -55°C to +125°C
TJ Junction Temperature ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ +175°C
ELECTRICAL SPECIFICATIONS
All Ratings: Tc= +25°C Unless Otherwise Specified
Parameter
OUTPUT CHARACTERISTICS
Test Conditions
Subgroup
MSK4201B 3
MSK4201 2
Group A
5
Min. Typ. Max. Min. Typ. Max.
Units
VDS(ON) Voltage (Each MOSFET)
ID=5A
1
-
1.5 1.8 -
1.5 2.16 V
2
-
2.2 2.4 -
-
-
V
3
-
1.1 1.2 -
-
-
V
Instantaneous Forward Voltage, Each MOSFET IS=5A 1
1
-
1.0 2.1 -
1.0
2.2
V
(Intrinsic Diode)
2
-
0.9 2.0 -
-
-
V
3
-
1.1 2.2 -
-
-
V
Reverse Recovery Time (Intrinsic Diode) 1
-
-
-
240 -
-
240 nS
Leakage Current, Each MOSFET
V+=70V
1
-
-
25
-
-
30
uA
V+=70V
2
-
-
250 -
-
-
uA
V+=70V
3
-
-
25
-
-
-
uA
VCC SUPPLY CHARACTERISTICS
VCC Supply Voltage Range 1
-
10 12
15 10 12
15
V
Quiescent Logic Current
VCC=12V
1
-
11
18
-
11
21 mA
(non-switching)
2
-
11
18
-
-
-
mA
3
-
11
18
-
-
-
mA
INPUT SIGNALS CHARACTERISTICS
Threshold Voltage
1
VCC=12V
1,2,3 0.8 1.5 2.7 0.8 1.5
2.7
V
SWITCHING CHARACTERISTICS 1 V+=28V, VCC=12V, IC=2A
Turn-On Propagation Delay (Includes Deadtime)
-
-
160 240 -
160
-
nS
Turn-Off Propagation Delay
-
-
85 128 -
85
-
nS
Rise-Time
-
-
36
54
-
36
-
nS
Fall-Time
-
-
170 255 -
170
-
nS
Dead-Time
Disable Function
dis
NOTES:
DIS>3.6V
-
-
100
-
-
100
-
nS
7
-
P/F
-
-
P/F
-
-
1 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
2 Industrial grade devices shall be tested to subgroup 1 unless otherwise specified.
3 Military grade devices ("B" suffix) shall be 100% tested to subgroups 1,2,3 and 7.
4 Subgroups 5 and 6 testing available upon request.
5 Subgroup 1,4 TA=TC= +25°C
2
TA=TC= +125°C
3
TA=TC= -55°C
6 Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
7 When applying power to the device, apply the low voltage followed by the high voltage or alternatively, apply both at the
same time. Do not apply high voltage without low voltage present.
8 Internal solder reflow temperature is 180°C, do not exceed.
9 Reference DLA SMD 5962-97629 for electrical specification for devices purchased as such.
2
8548-116 Rev. F 3/14