MSK115_15 Datasheet, PDF (2/7 Pages) M.S. Kennedy Corporation – Excellent Linearity - Class A/B Output

ABSOLUTE MAXIMUM RATINGS ⁸
±VCC
IOUT
VIN
TC
Supply Voltage ±50V ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Output Current 15A ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Differential Input Voltage ○ ○ ○ ○ ○ ○ ○ ○ ○ ±37V
Case Operating Temperature Range
(MSK115B) ○ ○ ○ ○ ○ ○ ○ ○ -○ 55°C to+125°C
(MSK115) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ -40°C to +85°C
TST
Storage
Temperature
Range
9
○
○
○ -65°C to +150°C
TLD Lead Temperature Range
(10 Seconds) 300°C ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
PD Power Dissipation ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ See S0A Curve
TJ Junction Temperature ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 175°C
ELECTRICAL SPECIFICATIONS
Parameter
Test Conditions 1
Group A
MSK115B
MSK115
Subgroup Min. Typ. Max. Min. Typ. Max.
STATIC
Supply Voltage Range ³
-
±10 -
±50 ±10 -
±45
Quiescent Current
VIN=0V
1
- ±22 ±35 - ±22 ±40
AV=-10V/V
2,3
- ±28 ±45 -
-
-
Thermal Resistance 3
Junction to Case @ 25°C
-
-
0.5 0.6
-
0.5 0.7
INPUT
Input Offset Voltage
VIN=0V AV=10V/V
1
-
±2 ±6
-
±2 ±10
Bal.Pins=NC
2,3
-
±3 ±12
-
-
-
Input Offset Adjust
RPOT=10KΩ Wiper to -VCC
7
Adjust to zero
Adjust to zero
AV=-10V/V
8A,8B
Adjust to zero
-
-
-
Input Bias Current
VCM=0V
1
- ±10 ±30 - ±10 ±50
Either Input
2,3
- ±15 ±250 -
-
-
Input Offset Current
VCM=0V
1
-
±5 ±30 -
±5 ±50
2,3
- ±10 ±100 -
-
-
Input Impedance 3
F=DC
-
50 250
-
35 250
-
Common Mode Range 3
-
- ±35
-
- ±35
-
Common Mode Rejection Ratio 3 F=100Hz VCM=±5V
-
80 100
-
74 100
-
OUTPUT
Output Voltage Swing
RL=500Ω AV=-10V/V
4
±35 ±37
-
±33 ±37
-
3
RL=10Ω RSC = 0Ω
-
±35 ±36
-
±33 ±36
-
Output Current, Peak
AV=-10V/V VOUT=MAX
4
15
-
-
10
-
-
Settling Time 2 3
0.1% 10V step
-
-
2
-
-
5
-
TRANSFER CHARACTERISTICS
Slew Rate
VOUT=±10V RL=500Ω AV=-10V/V
4
2.5 5
-
1
2.5
-
Open Loop Voltage Gain 3
RL=500Ω F=10Hz
4
95 105
-
85 105
-
Gain Bandwidth Product 3
RL=10Ω F=1 MHz
-
-
4
-
-
3
-
Units
V
mA
mA
°C/W
mV
mV
mV
mV
nA
nA
nA
nA
MΩ
V
dB
V
V
A
μS
V/μS
dB
MHz
NOTES:
1 Unless otherwise specified, ±VCC=±40VDC
2 AV= -1, measured in false summing junction circuit.
3 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
4 Industrial grade devices shall be tested to subgroups 1,4 and 7 unless otherwise specified.
5 Military grade devices ("B" suffix) shall be 100% tested to subgroups 1,2,3,4,7,8A and 8B.
6 Subgroups 5 and 6 testing available upon request.
7 Subgroup 1,4,7 TA=TC=+25°C
Subgroup 2,5,8A TA=TC=+125°C
Subgroup 3,6,8B TA=TC=-55°C
8 Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
9 Internal solder reflow temperature is 180°C, do not exceed.
2
8548-119 Rev. E 4/14