P1900 Datasheet, PDF (1/1 Pages) MPS Industries, Inc. – PASSIVE POWER FACTOR CORRECTION INDUCTORS

PASSIVE POWER FACTOR
CORRECTION INDUCTORS
P1900 SERIES
• Designed for use in off-line AC-DC pre-regulators circuits for
switching power converters applications
• Low core loss and high flux density
• Insulation class system: B (130°C), F (155°C) or H(180°C)
• Dielectric Withstanding Voltage (DWV): 2KV_RMS
• Operating Temperature: -20°C to +105°C
• RoHS Compliant Product
• Custom Design Available
ELECTRICAL PARAMETERS @ 25°C
Part
Number
L
(μH MIN)¹
Terminal³
DCR
I @ 80% L I @ 65% L I @ 50% L I @ 30% L Pins Dia.
(S-F)
(mΩ MAX)^{1, 2}
(A^DC)
(A^DC)
(A^DC)
(A^DC)
(Ø AWG)
LxWxH
(in. MAX)
PCB
Mounting
Layout
P19000
240
1-5, 2-4
28
P19001
290
1-5, 2-4
53
P19002
400
1-5, 2-4
120
P19003
440
1-5, 2-4
55
P19004
440
1-5, 2-4
55
P19005
490
1-5, 2-4
118
P19006
500
1-5, 2-4
90
P19007
820
2-5
95
P19008
1600
2-5
241
P19009
2000
2-5
286
16.50
14.80
10.60
12.20
12.20
11.20
11.40
7.50
6.40
5.70
1. Test conditions: 10KHz, 1V_RMS.
2. Combined resistance of the “x2” winding.
3. Only those assigned terminals will have the self-lead pins.

37.00
33.00
24.00
27.00
27.00
25.00
26.00
17.00
14.00
13.00
60.00
53.50
38.50
44.00
44.00
40.50
41.50
27.00
23.00
20.50
60.00
53.50
38.50
44.00
44.00
40.50
41.50
27.00
23.00
20.50
14 x 2
14 x 2
15 x 2
15 x 2
15 x 2
15 x 2
15 x 2
14
15
15
2.7x1.0x2.8
2.7x1.0x2.8
2.6x1.0x2.7
2.6x1.0x2.7
2.6x2.6x1.0
2.6x1.0x2.7
2.6x1.0x2.7
2.7x1.0x2.8
2.7x1.0x2.8
2.7x1.0x2.8
V / Fig. 2
V / Fig. 2
V / Fig. 3
V / Fig. 3
H / Fig. 4
V / Fig. 3
V / Fig. 3
V / Fig. 1
V / Fig. 1
V / Fig. 1
DIMENSIONS (mm)
VERTICAL
L
W
0.60
[15.24]
Figure 1
1.20
[30.48]
0.25
[6.35]
Figure 2
0.50
[12.70]
H
0.18
[4.57]
P19XXX MPS DC
123
Ø AWG
1.00
[25.40]
6
5
4
1
2
3
2.00
[50.80]
0.85
[21.59]
1.00
[25.40]
654
123
2.00
[50.80]
0.85
[21.59]
HORIZONTAL
Figure 3
Figure 4
L&W
1.575
[40.005]
0.20
0.984
ØL
[5.08] [25.000]
Typ.
6
54
P19XXX MPS DC
H
1.00
[25.40]
0.85
[21.59]
2
1
12
3
0.18
2
1
[4.57]
1.375
[34.925]
2.00
[50.80]
0.20
[5.08]
Typ.
Product performance is limited to specified parameters.Data is subject to change without prior notice.
Tel: [phone]
Fax: [phone]
SCHEMATICS
S
F
Dimensions
Unless otherwise specified, all tolerances are:
inch: .XX : ±0.015 .XXX : ±0.004
mm: X,X : ±0,38 X,XX : ±0,10
www.mpsind.com
[e-mail]