MA300RU Datasheet, PDF (2/2 Pages) MicroPower Direct, LLC – MA300RU SERIES

Model Selection Guide
www.micropowerdirect.com
Model
Number
MA324S-05RU
MA324S-05RU
MA324S-12RU
MA324S-15RU
MA324S-24RU
MA324D-05RU
MA324D-12RU
MA324D-15RU
MA348S-03RU
MA348S-05RU
MA348S-12RU
MA348S-15RU
MA348S-24RU
MA348D-05RU
MA348D-12RU
MA348D-15RU
Input
Voltage (VDC)
Current (mA)
Voltage
Nominal Range Full-Load No-Load ^(VDC)
24 9.0 - 36.0 134
30
3.3
24 9.0 - 36.0 158
30
5.0
24 9.0 - 36.0 152
30
12.0
24 9.0 - 36.0 151
30
15.0
24 9.0 - 36.0 154
30
24.0
24 9.0 - 36.0 130
30
±5.0
24 9.0 - 36.0 152
30
±12.0
24 9.0 - 36.0 152
30
±15.0
48 18.0 - 75.0 67
20
3.3
48 18.0 - 75.0 78
20
5.0
48 18.0 - 75.0 75
20
12.0
48 18.0 - 75.0 74
20
15.0
48 18.0 - 75.0 76
20
24.0
48 18.0 - 75.0 65
20
±5.0
48 18.0 - 75.0 76
20
±12.0
48 18.0 - 75.0 76
20
±15.0
Output
Current
(mA, Max)
750.0
600.0
250.0
200.0
125.0
±250.0
±125.0
±100.0
750.0
600.0
250.0
200.0
125.0
±250.0
±125.0
±100.0
Current
(mA, Min)
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
Efficiency
(%, Typ)
Reflected
Ripple
Current
(mA Typ)
Capacitive
Load
(µF, Max)
Fuse
Rating
Slow-Blow
(mA)
77
15.0
680
1,000
79
15.0
470
1,000
82
15.0
330
1,000
83
15.0
220
1,000
81
15.0
100
1,000
80
15.0
±220
1,000
82
15.0
±150
1,000
82
15.0
±100
1,000
77
10.0
680
500
80
10.0
470
500
83
10.0
330
500
84
10.0
220
500
82
10.0
100
500
80
10.0
±220
500
82
10.0
±150
500
82
10.0
±100
500
Notes:
1. When measuring output ripple, it is recommended that an external 3.3 µF ceramic capacitor be
placed from the +VOUT pin to the -VOUT pin for single output units and from each output to common
for dual output units.
2. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%.
3. Operation at no-load will not damage these units.
4. An external 220 µF/100V capacitor connected across the input pins is required to meet
EN61000-4-4 and EN61000-4-5.
5. Dual output units may be connected to provide a 10, 24 or 30 VDC output. To do this, connect the
load across the positive (+VOUT) and negative (-VOUT) outputs and float the output common.
6. The converter should be connected to a low ac-impedance source. An input source with a highly
inductive impedance may affect the stability of the converter. In applications where the converter
output loading is high and input power is supplied over long lines, it may be necessary to use
a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR
<1.0⍀ at 100 kHz) capacitor be mounted close to the converter. For 24V input units a 4.7 µF is
recommended; and for 48V units a 2.2 µF.
7. It is recommended that a fuse be used on the input of a power supply for protection. See the table
above for the correct rating.
Mechanical Dimensions
Derating Curve
For 3 kV Isolation, See MA300x-xxRUI Series Datasheet
For 2:1 Inputs, See MA300x-xxRW Series Datasheet
Pin Connections
Pin Single Dual
2, 3
-VIN
-VIN
9 No Pin Common
11
14
16
22, 23
NC
+VOUT
-VOUT
+VIN
-VOUT
+VOUT
Common
+VIN
NC: No Connection
MicroPower Direct
Mechanical Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.x = ±0.02 (±0.50)
• Tolerance x.xx = ±0.01 (±0.25)
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 • TEL: [phone] • FAX: [phone] • E-Mail: [e-mail]