H100I Datasheet, PDF (2/2 Pages) MicroPower Direct, LLC – Ultra-Miniature MiniDIP 1W, High Isolation DC/DC Converters

Model Selection Guide
Model
Number
H101I
H102I
H103I
H104I
H105I
H106I
H111I
H112I
H113I
H114I
H115I
H116I
H121I
H122I
H123I
H124I
H125I
H126I
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
5
4.5 - 5.5
278
25
5
4.5 - 5.5
267
25
5
4.5 - 5.5
260
25
5
4.5 - 5.5
256
25
5
4.5 - 5.5
257
25
5
4.5 - 5.5
257
25
12
10.8 - 13.2
116
16
12
10.8 - 13.2
112
16
12
10.8 - 13.2
109
16
12
10.8 - 13.2
107
16
12
10.8 - 13.2
107
16
12
10.8 - 13.2
107
16
24
21.6 - 26.4
58
8
24
21.6 - 26.4
56
8
24
21.6 - 26.4
55
8
24
21.6 - 26.4
54
8
24
21.6 - 26.4
54
8
24
21.6 - 26.4
54
8
Voltage
(VDC)
3.3
5.0
9.0
12.0
15.0
24.0
3.3
5.0
9.0
12.0
15.0
24.0
3.3
5.0
9.0
12.0
15.0
24.0
Output
Current
(mA, Max)
300.0
200.0
111.0
83.3
66.6
41.6
300.0
200.0
111.0
83.3
66.6
41.6
300.0
200.0
111.0
83.3
66.6
41.6
Other outputs are available.
Contact the factory for details at:
[e-mail]
Derating Curve
Current
(mA, Min)
5.0
4.0
2.0
2.0
2.0
2.0
5.0
4.0
2.0
2.0
2.0
2.0
5.0
4.0
2.0
2.0
2.0
2.0
Notes:
1. Output load regulation is specified for a load change of
20% to 100%.
2. When measuring output ripple, it is recommended that
an external 0.33 µF ceramic capacitor be placed from the
+Vout pin to the -Vout pin.
3. Operation at no-load will not damage these units. How-
ever, they may not meet all specifications.
4. The 5V, 12V and 24V input units do not require external
components to operate, but the use of a low ESR capaci-
tor (approximately 10 uF, ESR <1.0Ω at 100 kHz) mounted
close to the converter input pins is recommended.
For 48 VDC input units, an input capacitor should always be
used. Dependent upon the application, a value between
4.7 µF and 47 uF should be sufficient.
5. It is recommended that a fuse be used on the input of a
power supply for protection. See the table above for the
correct rating.
Capacitive
Mechanical Dimensions
Load
(µF Max)
220
Efficiency
(%, Typ)
72
75
77
78
78
78
72
75
77
78
78
78
72
75
77
78
78
78
Fuse Rating
Slow-Blow
(mA)
500
500
500
500
500
500
200
200
200
200
200
200
100
100
100
100
100
100
Pin Connections
Pin Function
1
-Vin
4
+Vin
5
+Vout
7
-Vout
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the top
of the unit
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072 • TEL: [phone] • FAX: [phone] • E-Mail: [e-mail]