G200EI Datasheet, PDF (2/2 Pages) MicroPower Direct, LLC – High Isolation, 2W Low Cost, MiniDIP DC/DC Converters

Model Selection Guide
Model
Number
G201EI
G202EI
G203EI
G204EI
G205EI
G206EI
G207EI
G208EI
G211EI
G212EI
G213EI
G214EI
G215EI
G216EI
G217EI
G218EI
G221EI
G222EI
G223EI
G224EI
G225EI
G226EI
G227EI
G228EI
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
5
4.5 - 5.5
500
30
5
4.5 - 5.5
494
30
5
4.5 - 5.5
488
30
5
4.5 - 5.5
476
30
5
4.5 - 5.5
488
30
5
4.5 - 5.5
482
30
5
4.5 - 5.5
470
30
5
4.5 - 5.5
470
30
12 10.8 - 13.2 208
15
12 10.8 - 13.2 201
15
12 10.8 - 13.2 198
15
12 10.8 - 13.2 196
15
12 10.8 - 13.2 201
15
12 10.8 - 13.2 198
15
12 10.8 - 13.2 194
15
12 10.8 - 13.2 194
15
24 21.6 - 26.4 103
8
24 21.6 - 26.4 99
8
24 21.6 - 26.4 98
8
24 21.6 - 26.4 97
8
24 21.6 - 26.4 99
8
24 21.6 - 26.4 98
8
24 21.6 - 26.4 96
8
24 21.6 - 26.4 96
8
Voltage
(VDC)
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
Output
Current
(mA, Max)
400.0
222.0
167.0
133.0
±200.0
±111.0
±83.0
±67.0
400.0
222.0
167.0
133.0
±200.0
±111.0
±83.0
±67.0
400.0
222.0
167.0
133.0
±200.0
±111.0
±83.0
±67.0
Current
(mA, Min)
40.0
23.0
17.0
14.0
±20.0
±12.0
±9.0
±7.0
40.0
23.0
17.0
14.0
±20.0
±12.0
±9.0
±7.0
40.0
23.0
17.0
14.0
±20.0
±12.0
±9.0
±7.0
Load
Regulation
(%, Max)
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
Efficiency
(%, Typ)
80
81
82
84
82
83
85
85
80
83
84
85
83
84
86
86
81
84
85
86
84
85
87
87
Notes:
1. Output load regulation is specified for a load change of 10% to
100%.
2. These units should not be operated with a load under 10% of
full load. Operation at no-load may cause damage to the unit.
3. These converters will operate without external components.
However, when measuring output ripple, it is recommended
that an external ceramic capacitor be placed from the +Vout
pin to the -Vout pin for single output units and from each out-
put to common for dual output units. An input capacitor will
enhance stability over temperature and input line variations.
Recommended capacitor values are given in the table below.
For applications requiring very low output noise levels, a simple
LC filter should be effective.
Vin
Input
Capacitor
Vout
Output Capacitor
Single Dual
Derating Curve
5 VDC 4.7 μF 5 VDC 10.0 μF 4.7 μF
12 VDC
24 VDC
2.2 μF
1.0 μF
9 VDC
12 VDC
15 VDC
4.7 μF
2.2 μF
1.0 μF
2.2 μF
1.0 μF
0.47 μF
Mechanical Dimensions
4. Dual output units may be connected to provide a 10V, 18V, 24V
or 30 VDC output. To do this, connect the load across the posi-
tive (+Vout) and negative (-Vout) outputs and float the output
common
5. It is recommended that a fuse be used on the input of a power
supply for protection. See the Model Selection table above for
the correct rating.
Fuse Rating
Slow-Blow
(mA)
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
500
500
500
250
250
250
250
250
250
250
250
Pin Connections
Pin Single Dual
Pin
1 -Vin -Vin
9
7
NC
NC
10
8 +Vout +Vout
14
Single
No Pin
-Vout
+Vin
Dual
Common
-Vout
+Vin
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the top of the unit
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072 • TEL: [phone] • FAX: [phone] • E-Mail: [e-mail]